Rex Lint wrote:
> Don,
>
> The Teflon rod would spread the weight of the tower over 4 square inches or
> so: marty's would spread it over 40 or so, about a 10 to 1 difference. I'd
> think deformation of a sheet of Teflon would not have a safety issue,
> wouldn't you? The tower is guyed.
>
> He HAS, however, built a home-made capacitor to ground. Depending on the
> value of that capacitor, screwey things might arise regarding RF current to
> ground, but I 'spect it will work OK anyway.
>
And that Teflon will still "cold flow" leading to a slow change in
capacitance.
But didn't he say it was a "cutting board" 1" thick. I seriously doubt
it is Teflon, but rather like all cutting boards I've seen that weren't
wood , made of PVC
A standard size cutting board made of 1" Teflon would be *very* expensive.
73
Roger (K8RI)
> Rex
> K1HI
>
> -----Original Message-----
> From: towertalk-bounces@contesting.com
> [mailto:towertalk-bounces@contesting.com] On Behalf Of n8de@thepoint.net
> Sent: Wednesday, December 23, 2009 12:15 PM
> To: brahmangou@aol.com
> Cc: jperalta4@verizon.net; towertalk@contesting.com
> Subject: Re: [TowerTalk] Making an insulated base for 80 meter vertical from
> Rohn 25
>
> One comment on Teflon.
>
> It is SOFT and will deform rather easily under stress, whether expansion OR
> compression. Do some testing before you put a lot of force on it.
>
> My original idea was to use Teflon rod for my insulated tower bases, but
> changed that IMMEDIATELY upon discovering the deformation that occurred just
> with the weight of the base legs on the insulators in static position.
>
> Now using (as previously done) fiberglass rod which can be purchased in 6'
> lengths at a farm supply store, disguised as 'electric fence posts'. They
> are exactly the right size for my purpose, being 1.25"
> in diameter, and fit snugly within the tower leg supports.
>
> Good luck,
> 73
> Don
> N8DE
>
> Quoting brahmangou@aol.com:
>
>
>> Hi Guys,
>>
>> I got a few emails asking where I got the insulated base. I made it.
>> The insulated legs on the market are pretty expensive, and I didn't
>> like that they are in tension and compression when the tower moves
>> with the wind and under other external forces. It appeared to me, and
>> I may be wrong, that the insulating material might not be as
>> strong/durable as the original tower legs.
>>
>> I bought a 1" thick 24" square HDPE cutting board from a commercial
>> restaurant supply , about 18 dollars, and drilled it to fit over the
>> j-bolts in
>> a standard Rohn 3'x3'x4' concrete tower base. I put the Rohn tilt
>> base on top of the cutting board. There are several machine shops on
>> ebay that sell PTFE teflon machining end pieces, leftovers. I bought
>> a couple of short 1 1/2" teflon rod pieces, 6 dollars, and
>> drilled/turned them to fit in the annular space between the bolt
>> holes in the tilt base and the edges of the j-bolts as insulating
>> bolt sleeves. Then I took a short piece of 3" teflon rod, 3 dollars,
>> and sawed 1/2" thick disks off of it. I drilled through the disks and made
>>
> insulating washers for each of the base bolts.
>
>> This way all of the plastic parts are always in compression, at their
>> strongest. I used teflon for all of the parts that are exposed to the
>> sun to avoid UV breakdown of the insulators, also teflon is a superior
>>
> insulating
>
>> material for the thinner (3/16" thick) bolt sleeves. By using the
>> tilt base, I
>> can lower the tower to make adjustments and repairs in the future ( not
>> getting any younger, hi hi). I'm ready to install install the
>> tower sections
>> and run the feed line as soon as the weather clears up.
>>
>> Marty Haley AB5GU@ARRL.NET
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>>
>
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|