Don:
I'm not sure what advantage mounting the box upside down would offer.
In fact, the upfacing lid edge would funnel water into the upturned lid,
ensuring that the drain holes would be needed. Plus, I didn't fasten the
variable cap onto anything; it just sits on the bottom of the shoebox. So
I'd have to attached it to the box (more holes) somehow.
I could, however, go out right now and put a couple of wire ties around
the box, but I didn't have them on hand at the time and hadn't thought of it
since.
73 de
Gene Smar AD3F
----- Original Message -----
From: <n8de@thepoint.net>
To: "Gene Smar" <ersmar@verizon.net>
Cc: "Robert West" <robert.west@eatmoresoap.com>; <towertalk@contesting.com>;
<GlagowskiT@acm.org>; "John Kemker" <john@kemker.org>
Sent: Thursday, August 13, 2009 10:39 PM
Subject: Re: [TowerTalk] weatherproof plastic enclosures
> Gene,
> Why didn't you mount it upside-down and use some long cable-ties to
> hold the lid on the BOTTOM?
> Don
> N8DE
>
> Quoting Gene Smar <ersmar@verizon.net>:
>
>> TT:
>>
>> I've had a plastic shoebox made by Tucker out at my tower since Feb
>> of
>> 2002 to hold the gamma cap for my shunt feed. It's still in good shape,
>> although the plastic lid is a bit faded. Occasionally I have to go out
>> and
>> replace the lid after a heavy wind, but unless the lid is off the
>> interior
>> has been dry. I did drill four 1/8 inch drain holes in the bottom, which
>> probably helps in the dryness department. See photo of the new box at:
>> http://s83.photobucket.com/albums/j282/ersmar/?action=view¤t=Capacitor.jpg
>>
>> The box's location is in partial shade so it doesn't get full-on
>> sunlight. It's cheap enough that if it cracks I'd replace it in kind.
>> Of
>> course, my tower is in the back yard, not the Lower Forty, so the trip
>> out
>> there isn't too inconvenient.
>>
>>
>> 73 de
>> Gene Smar AD3F
>>
>> ----- Original Message -----
>> From: "John Kemker" <john@kemker.org>
>> To: "Robert West" <robert.west@eatmoresoap.com>
>> Cc: <towertalk@contesting.com>; <GlagowskiT@acm.org>
>> Sent: Thursday, August 13, 2009 7:08 PM
>> Subject: Re: [TowerTalk] weatherproof plastic enclosures
>>
>>
>>> The Rubbermaid Roughneck series might work well. The Sterilite brand
>>> are, in my opinion, junk to begin with. Even brand new, they can be
>>> brittle and break easily. Check in the outdoors/garden/etc section for
>>> them.
>>>
>>> Robert West wrote:
>>>> What about a UV rating for those? Have you used any of them in
>>>> sunlight
>>>> for
>>>> an extended period of time?
>>>>
>>>>
>>>>
>>>> -----Original Message-----
>>>> From: towertalk-bounces@contesting.com
>>>> [mailto:towertalk-bounces@contesting.com] On Behalf Of Terry G.
>>>> Glagowski
>>>> Sent: Wednesday, August 12, 2009 8:05 AM
>>>> To: towertalk@contesting.com
>>>> Subject: Re: [TowerTalk] weatherproof plastic enclosures
>>>>
>>>> There's and even MORE cost effective solution... available at WALMART,
>>>> etc...
>>>> Consider using the plastic boxes intended for storage of clothes, other
>>>> items,
>>>> under the bed (sort of like Tupperware).
>>>> As long as they have a top that CLIPS / CLAMPS on so the wind can't
>>>> blow
>>>> it
>>>> off,
>>>> they work fine for covers to COAX junction boxes outside, etc, at a
>>>> cost
>>>> of
>>>> under $10 !!!
>>>> Terry / W1TR
>>>>
>>>> -----Original Message-----
>>>> Message: 1
>>>> Date: Mon, 10 Aug 2009 17:47:39 -0400
>>>> From: "Robert West" <robert.west@eatmoresoap.com>
>>>> Subject: Re: [TowerTalk] weatherproof plastic enclosures
>>>> To: "'Dan Zimmerman N3OX'" <n3ox@n3ox.net>, <towertalk@contesting.com>
>>>> Message-ID: <004f01ca1a04$2ee10290$8ca307b0$@west@eatmoresoap.com>
>>>> Content-Type: text/plain; charset="us-ascii"
>>>>
>>>> I've been using the very same boxes from Home Depot. The 12x12x6
>>>> versions
>>>> are
>>>> 40 bucks around here and are darn tough.
>>>>
>>>> Bob-
>>>>
>>>>
>>>> -----Original Message-----
>>>> From: towertalk-bounces@contesting.com
>>>> [mailto:towertalk-bounces@contesting.com] On Behalf Of Dan Zimmerman
>>>> N3OX
>>>> Sent: Monday, August 10, 2009 2:30 PM
>>>> To: towertalk@contesting.com
>>>> Subject: Re: [TowerTalk] weatherproof plastic enclosures
>>>>
>>>>
>>>>> Does anyone know who makes the NEMA-4 sealed plastic enclosures that
>>>>> Array Solutions uses for their baluns?
>>>>>
>>>>>
>>>>
>>>> They look like PVC junction boxes to me. The onese I have are made by
>>>> Carlon
>>>> and came from Home Depot:
>>>>
>>>> http://www.carlon.com/Master%20Catalog/Junction_Boxes_Brochure.pdf
>>>>
>>>> http://n3ox.net/projects/stepperswitch/switchbox_ext_lg.JPG
>>>>
>>>> I think another company makes the ones for Array Solutions.
>>>>
>>>> 73,
>>>> Dan
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> TowerTalk mailing list
>>>> TowerTalk@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/towertalk
>>>>
>>>> _______________________________________________
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> TowerTalk mailing list
>>>> TowerTalk@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/towertalk
>>>>
>>>
>>> _______________________________________________
>>>
>>>
>>>
>>> _______________________________________________
>>> TowerTalk mailing list
>>> TowerTalk@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|
