Dave Johnson wrote:
> Hey Tom,
>
> >From what you said, it sure sounds like a connector problem. How about
> getting a boom truck with a man basket. It would have no problem lifting
> you to 80 feet. For anyone not familiar, a boom truck is a small crane
> mounted on a flat bed truck. They are much less expensive to rent than a
> crane. There should be a crane rental company or a sign company in Iron
> Mountain, MI that has one. The important thing would be to anticipate what
> you may need to fix the problem and have it ready because the boom truck
> rents by the hour.
>
>
Most of the boom trucks and Hy-Rangers I've seen go to 40 or 60 feet
although I've seen a few that go to 90. HOWEVER <:-)) The first time up
in a 60, let alone a 90 footer is "an experience" akin to the feeling
I'd imagine you'd get standing on top of 90' of un-guyed ROHN 25G.
Although secure, it certainly doesn't feel like it to the
"uninitiated". It might be difficult to rent a 90 footer due to the
liability issue as well. When you get that arm extended nearly straight
it feels anything but solid and any control input results in what feels
like really *quick* response <LOL> For the most stability you work off
the back of the truck and never raise the boom without putting down the
outriggers.
I don't know how much the boom trucks and Hy-Rangers run around here,
but I can get a crane with extension (for working above 100') with an
operator for *about* $300 per hour. With a good operator and some one
experienced riding in the cage you can get what would be a couple days
work done in just a few hours if everything is prepared ahead of time.
Unfortunately there is no way I can get one into our driveway. The road
is only two cars wide with a small bridge coming in. They can't make
the turn. We'd have to lay another 15-20 foot of culvert, put at least 2
of not 3 large truck loads of dirt on top and then my asphalt driveway
would never be the same and they could only get within about 75 feet of
the tower base. <sigh>
73
Roger (K8RI)
> Good Luck,
>
> Dave - K4SSU
>
>
>
> ----- Original Message -----
> From: "Tom Martin" <tmartin@chartermi.net>
> To: <TowerTalk@contesting.com>
> Sent: Monday, April 20, 2009 11:36 PM
> Subject: [TowerTalk] SWR Problem
>
>
>
>> About three weeks ago, as I tried to work a YK on 40 CW, my SWR on the 40
>> meter shortened dipole jumped from 1:1 to 5:1. At the time we were
>> experiencing a heavy, wet snowfall. The antenna is the driven element of
>> a Mosley S-402 at 80 feet. I assumed that it was possible that snow had
>> accumulated on the feed point causing the jump in SWR. I shut down the
>> amp and missed the YK. I'm glad that I have an Alpha 99! The amp went to
>> the Fault mode and saved the tubes.
>>
>> After we had some dry weather, I tried again and the SWR was a steady 5:1.
>> I checked coax connectors at the base of the tower and even cut off some
>> coax to see if there was any water in the line. Nothing was found. A few
>> years ago, on the same antenna, but with the reflector attached, I cut the
>> coax and water ran out. Since that time, I have replaced the coax to the
>> driven element and removed the reflector. I installed a 4 element SteppIR
>> and didn't want more wind load. The rotating driven element has done very
>> well on 40 DX.
>>
>> Last week, during a very warm spell for April here in the U.P., I tried
>> the antenna and the SWR was perfect. I even worked a few stations, using
>> the Alpha at 1 KW with no problem. After a few contacts, the SWR went to
>> 5:1 again even at 25 watts.
>>
>> In order to work the S04, I erected a delta loop, corner fed with the apex
>> at 70 feet. It worked very well. However, the 40 meter driven element
>> was 2 S-units better on receive! I am presently transmitting on the loop
>> and receiving on the 40 driven. My fingers are cramped from switching
>> back and forth! I can't get to the antenna without a bucket truck.
>> Unfortunately, none of the trucks in my area go to 80 feet! A climber
>> wouldn't get to the antenna either, since it's 8 feet above the SteppIR.
>> I sure don't want to go through the process of removing the rotor and
>> lowering the mast. That is unless, K4FMX wants to climb. HI!
>>
>> The question I have is why does the antenna receives so well with a
>> terrible SWR? Is there just one thread of copper attached at the feed
>> point that allows it to receive but when power is fed to it, it heats up
>> and the SWR goes high? Is it possible that the wet snow and high power
>> combined to cause a break in the center conductor of the coax at the feed
>> point? I've checked the connection with binoculars and it looks OK.
>> Also, when I installed the antenna last October, I made the connection as
>> waterproof as possible and formed loop above the feed point so that water
>> wouldn't run back toward the pigtail.
>>
>> This is sure frustrating!
>>
>> 73,
>>
>> Tom W8JWN
>>
>> --
>> I am using the free version of SPAMfighter.
>> We are a community of 6 million users fighting spam.
>> SPAMfighter has removed 3581 of my spam emails to date.
>> Get the free SPAMfighter here: http://www.spamfighter.com/len
>>
>> The Professional version does not have this message
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|