Barrie, Roger, et al,
I will look into the LMR 600 stripper. I'm pretty sure that we have
supplied that in past.
Ref FREE stripper from Times..... Barrie, I suspect you were VERY LUCKY,
and considering GE now owns Times, GE 's recent qtr. results were lower than
predicted (bad) and GE has been selling Iran.... I suspect your (our) "
luck is out" HI Steve
DAVIS RF Co., Div. of Orion Wire Co.
Wire, Cable, RF Connectors and wire aerial parts. LMR, Heliax, Eupen
Commercial / Military / & Custom Cable Design
tel: 978-369-1738 Fax: 978-369-3484
www.DavisRF.com
----- Original Message -----
From: "Barrie Smith" <barrie@centric.net>
To: "Roger (K8RI)" <K8RI-on-TowerTalk@tm.net>; "Steve Davis -Davis RF Co."
<sdavis@davisrf.com>
Cc: <towertalk@contesting.com>
Sent: Friday, September 26, 2008 6:53 PM
Subject: Re: [TowerTalk] Cable Stripper Cost savings-Response by DAVIS RF
Co.
>
> ----- Original Message -----
> From: "Roger (K8RI)" <K8RI-on-TowerTalk@tm.net>
> To: "Steve Davis -Davis RF Co." <sdavis@davisrf.com>
> Cc: <towertalk@contesting.com>
> Sent: Friday, September 26, 2008 2:40 PM
> Subject: Re: [TowerTalk] Cable Stripper Cost savings-Response by DAVIS RF
> Co.
>
>
>> Hi Steve,
>>
>> Do you have or know where I could find a stripper for LMR-600? Is such
>> a thing even available, or if so, at a reasonable price?
>
> Several years ago I contact Times Microwave regarding a stripper for
> LMR-600. At that time, they had them in stock. And, they fellow I spoke
> with sent me one FREE!
>
> 73, Barrie, W7ALW
>>
>> Steve Davis -Davis RF Co. wrote:
>>> Hi Folks, The RFA-4087, as Larry points out, is a real good stripper.
>>> Sold
>>> for $ 48 or more elsewhere (above the mfr. suggested list), we sell it
>>> for $
>>> 36.00, below mfr. sug. list). We also have crimp tools with
>>> interchangeable die (vs. many you have to buy the tool with permanently
>>> affixed die for one cable or similar sized cables).
>>>
>>> Any parts, tools, PolyPhaser, etc. related to our core biz of wire,
>>> cable and custom cable design, please run by me as I think you will
>>> always
>>> find the price, tech insight, product experience and Customer
>>> Satisfaction
>>> to be noteworthy.
>>> 73, Steve , K1PEK
>>>
>>> DAVIS RF Co., Div. of Orion Wire Co.
>>>
>>> Wire, Cable, RF Connectors and wire aerial parts. LMR, Heliax, Eupen
>>>
>>> Commercial / Military / & Custom Cable Design
>>>
>>> tel: 978-369-1738 Fax: 978-369-3484
>>> www.DavisRF.com
>>>
>>>
>>>
>>> TowerTalk@contesting.com:
>>> I really like the RFA-4087 from RF Parts
>>> (http://www.rfparts.com/coax_accessories.html , under "Coax Strippers
>>> and
>>> Prep Tools" toward the bottom of the page). Sells for $48.90 and works
>>> with
>>> LMR-400, LMR-400UF, RG8, 213, 214 and 9913 per their catalog. I used
>>> mine on
>>> regular LMR400 for a complete antenna installation at my new QTH. Never
>>> had
>>> to change the blades. It looks like a cheap-o plastic stripper in the
>>> catalog, but it is die-cast zinc and heavy duty. I have used the Ripley
>>> Cablematic on RG-8 and much prefer the RFA-4087. These are really slick.
>>> Couple one of these with a crimp connector made for the LMR-400 and you
>>> have
>>> a solid, quick connection.
>>>
>>> - Larry K5RK
>>>
>>>
>>> _______________________________________________
>>>
>>>
>>>
>>> _______________________________________________
>>> TowerTalk mailing list
>>> TowerTalk@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/towertalk
>>>
>>>
>>
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>
>
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|