It's a can and bottle opener, commonly given away at paint stores.
73,
geo - n4ua
> -----Original Message-----
> From: towertalk-bounces@contesting.com [mailto:towertalk-
> bounces@contesting.com] On Behalf Of K1TTT
> Sent: Friday, April 04, 2008 9:38 AM
> To: reflector -tower; reflector cq-contest; YCCC; Rlx; Nobarc
> Subject: [TowerTalk] mystery tool and damaged 40m antennas
>
> Take a look at the picture of the tool next to a pencil for size
> comparison:
> http://www.k1ttt.net/images/2008_40m4lldd_repair_1.jpg
>
> This tool was uniquely suited for one particular job while
disassembling
> an
> ice and wind damaged 40m4lldd yagi. Out of all the tools in all my
> various
> tool boxes this one stood out for this one specific task.
>
> Can you identify:
> 1. What it's original purpose(s) were?
> 2. What it would be used for in a 40m yagi disassembly?
>
>
> Pictures of the 40m damage in progress are below... We had 3 ice
storms in
> 2
> weeks, 2 of them were followed immediately by strong winds. Besides
> damage
> to both 40m4lldd's there were several bent elements on 20m4dx yagis
that
> had
> survived several years with 'normal' ice and wind. Something
interesting
> to
> note is that the loading rods on the 40m4lldd's did not provide any
> mechanical strength to the elements even though they look like they
would
> act as trusses. The elements all bent on the same side of the
antennas
> because the wind hit them from the side while the element was already
bent
> down under the ice load. The same mechanism damaged all 4 elements of
the
> top fixed European 20m yagi that was sideways to the wind, while the
> rotatable one above it only had 1 slightly bent element since it was
> pointing into the NW wind at the time. The loading rods broke all on
the
> same side because the wind shifted while the elements were bent so one
> side
> of the loading section was stretched against the side of the element.
>
> Tower is 180' of Rohn-55 with the 40m4lldd's on ring rotors at 70' and
> 170'.
>
> 2/2 Top 40m with ice and wind
> http://www.k1ttt.net/images/2008_feb_02_40m_ice_1.jpg
>
> 2/2 Top 40m with ice, note how on the left side all 4 elements are
bent at
> the sme place and the loading rods are below the element tubing.
> http://www.k1ttt.net/images/2008_feb_02_40m_ice_2.jpg
>
> 2/2 Top 40m with ice element closeup
> http://www.k1ttt.net/images/2008_feb_02_40m_ice_3.jpg
>
> 2/2 Bottom 40m with ice
> http://www.k1ttt.net/images/2008_feb_02_40m_ice_5.jpg
>
> 2/7 Top 40m with ice and wind, round 2 of the storms you can see the
1st
> loading rod broke on the right element. Eventually all 4 elements
ended
> up
> with 1 broken rod, all on the same side.
> http://www.k1ttt.net/images/2008_feb_07_40m_ice_11.jpg
>
> 2/7 Top 40m with ice and wind, slightly crooked elements.
> http://www.k1ttt.net/images/2008_feb_07_40m_ice_13.jpg
>
> 2/7 Top 40m broken loading rod closeup
> http://www.k1ttt.net/images/2008_feb_07_40m_ice_8.jpg
>
> Removal of the damaged antennas was done by XX-Towers on 3/7:
> Rigging bottom 40m, tram line is cable coming down to left.
> http://www.k1ttt.net/images/2008_mar_07_kc1xx_2.jpg
>
> Bottom one coming down
> http://www.k1ttt.net/images/2008_mar_07_kc1xx_4.jpg
>
> Bottom one wide view
> http://www.k1ttt.net/images/2008_mar_07_kc1xx_5.jpg
>
> Closeup of broke loading rod end, its really not pulled out, the
shorting
> bar held and the rod broke. The ss saddle and eye arrangement on the
> philly
> cable is my modification to prevent the philly from being cut on the
side
> of
> the small holes it used to go through on the shorting block. M2 has
> modified the design with a strain relief to prevent that on new ones.
> http://www.k1ttt.net/images/2008_mar_07_kc1xx_6.jpg
>
> Rigging the top 40m, tram line is hard to see but comes down between
guy
> wires toward bottom.
> http://www.k1ttt.net/images/2008_mar_07_kc1xx_7.jpg
>
> Rigging top, wide view.
> http://www.k1ttt.net/images/2008_mar_07_kc1xx_8.jpg
>
> Liftoff of top one.
> http://www.k1ttt.net/images/2008_mar_07_kc1xx_10.jpg
>
> Top one starting down
> http://www.k1ttt.net/images/2008_mar_07_kc1xx_12.jpg
>
> Interesting rigging, use ring rotor supports and boom brace to spread
load
> to 4 points on boom.
> http://www.k1ttt.net/images/2008_mar_07_kc1xx_13.jpg
>
> Insurance has already paid off and I am awaiting delivery of a new
125mph
> 40m4lldd for the top. For the bottom one I salvaged parts from the
top
> one
> to make it whole and have purchased aluminum to beef it up similar to
how
> the 125mph elements are done. I also am waiting delivery of a 20m4dx
to
> be
> used for parts to replace bent element sections on those antennas.
>
> Of course I am writing this today because we are now getting
snow/freezing
> rain/rain/whatever out there and I figured I can wait a while to
continue
> repairs.
>
> David Robbins K1TTT
> e-mail: mailto:k1ttt@arrl.net
> web: http://www.k1ttt.net
> AR-Cluster node: 145.69MHz or telnet://dxc.k1ttt.net
>
>
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
------------------------------------------------------------------------------------------------
This message is for the designated recipient only and may
contain privileged, proprietary, or otherwise private information.
If you have received it in error, please notify the sender
immediately and delete the original. Any unauthorized use of
this email is prohibited.
------------------------------------------------------------------------------------------------
[mf2]
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|
