Towertalk
[Top] [All Lists]

[TowerTalk] Potting Baluns

To: <TOWERTALK@contesting.com>
Subject: [TowerTalk] Potting Baluns
From: "K8RI" <K8RI-on-TowerTalk@tm.net>
Date: Tue, 5 Feb 2008 13:48:31 -0500
List-post: <mailto:towertalk@contesting.com>
Just a thought here:

When putting something together like a balun do you want to seal it, weather 
proof it, make it rugged, reliable?
The odds are the answer is "all of the above". If it is then it's likely the 
job is going to be *permanent*!  IOW the parts are not going to be reusable.

Only one method is the most reliable and that is potting, but if potting 
then the capacity of the  balun and the ability to get rid of heat have to 
be taken into account. If the balun is going to be inside a container such 
as a PVC sleeve/tube like the old KLM and many of today's the RTV, be it 
regular or non acetic is unlikely to cure properly or if it does it'll take 
months to do so.  remember this stuff will cure in the tube eventually.

One thing that should be pointed out right at the start: RTVs are not 
designed to be used as potting compounds. But that requires defining Room 
Temperature Silicones or RTVs. Originally they were the _one_part_ materials 
that smelled like Acetic Acid and later the non-corosive types were 
developed. *Outside* industry the term RTV has been applied to anything the 
cures at room temperature. Last I knew there were no two part RTVs. Those 
are sealants and potting compounds.  Another variant that came along is the 
CONDUCTIVE RTV . the only color in which I've ever seen the conductive 
*stuff* is black.  That doesn't mean all black RTVs are conductive as they 
aren't.

So, were it me, and it's not, I'd use either a two part Silicone potting 
compound which is likely to be quite expensive, or an epoxy of a fairly low 
viscosity.  West Systems (TM) makes a very nice two part epoxy that should 
do the trick, it's inexpensive (expensive and inexpensive are relative terms 
here),easy to use, and readily available at most boating supply stores. 
Like many epoxies it is exothermic and it does get HOT.<:-)).  This approach 
has a number of  advantages over the RTVs. It is STRONG (If you want even 
stronger you can mix in what are called "mill fibers"), It is water AND 
moisture proof. RTVs are water proof, but not moisture proof. Also the cure 
time is a known factor that can be varied a bit to suit conditions.  I 
prefer Vinyl Ester Resin as it has a lower viscosity than the epoxy and I 
have a lot of it. Unfortunately it only comes in gallons and it has a very 
short shelf life compared to the epoxy family. It also uses a rather nasty 
catalyst that makes it expensive to ship.

It may take a little practice to do a good job of potting, but the results 
are worth the time. Also, any potting job should be considered *Permanent*. 
IOW the parts are unlikely to be reuseable but there's nothing in a balun 
that should be considered expensive. OTOH I do realize some of us have to 
pinch pennies by necessity where even PL-259s and SO-239s get reused. (been 
there and done that)
The nice thing is by rolling your own, you can build a balun with ratings 
high enough to withstand considerabley higher voltages and currents handled 
by the regularly available "store bought" stuff.

73, good luck, and happy potting,

Roger (K8RI)

BTW I retired as a project manager from one of the major corporations that 
produces a series of RTVs.

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>