Towertalk
[Top] [All Lists]

Re: [TowerTalk] How does the DX engineering 4Sq phasing box compare?

To: Mark Robinson <markrob@mindspring.com>
Subject: Re: [TowerTalk] How does the DX engineering 4Sq phasing box compare?
From: Tim Duffy K3LR <k3lr@k3lr.com>
Reply-to: k3lr@k3lr.com
Date: Thu, 05 Jul 2007 16:56:49 -0400
List-post: <mailto:towertalk@contesting.com>
I think there is some confusion going on here.
There are two versions of DX Engineering boxes that I am aware of.

The 1st was a copy of the Comtek box. Built by the former DX Engineering company
in Oregon (not to be confused with the even older DX Engineering company that
built RF speech processors for Drake and Collins gear) This Comtek clone can be
used for TX and RX. I measured the performance of this box (80 meter version)
and found it to be close to proper phasing, but not as good as the Comtek.

The 2nd (current DX Engineering company in Ohio) 4 square box is RX only. It was
designed by W8JI and is available direct from DXE. I use one on 160 meters with
mobile antennas for the vertical elements and it works great.

The Ohio DX Engineering company has said that they may produce a 4 square box (8
directions) that would TX and RX, but it has not come to market yet as far as I
know.

73!
Tim K3LR


Mark Robinson wrote:

> Agreed but I have worked quite a few stations on 80m who were using the
> Comtek box and they had good directional characteristics from their arrays.
> If you have a nice flat location then the Comtek box should work well but it
> is not so easy to tweak as the DXE box.
>
> Mark N1UK G3ZZM
>
> ----- Original Message -----
> From: "Rick Karlquist" <richard@karlquist.com>
> To: "jeremy-ca" <km1h@jeremy.mv.com>
> Cc: <towertalk@contesting.com>
> Sent: Thursday, 05 July, 2007 3:35 PM
> Subject: Re: [TowerTalk] How does the DX engineering 4Sq phasing box
> compare?
>
> > IMHO, the DXE is the first box to do it the "right" way.
> > It is also fairly expensive.  I don't own any of these,
> > but the DXE is similar to stuff I have homebrewed that
> > worked well.  It looks like a good implementation.
> >
> > Rick N6RK
> >
> > jeremy-ca wrote:
> >> Im considering going to a 4sq for 80M and possibly 160 and wonder how the
> >> DX
> >> Engr compares to Comtek and others?
> >>
> >> Carl
> >> KM1H
> >>
> >>
> >> _______________________________________________
> >>
> >>
> >>
> >> _______________________________________________
> >> TowerTalk mailing list
> >> TowerTalk@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/towertalk
> >>
> >>
> >
> >
> > _______________________________________________
> >
> >
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>