I can't resist. I have a wench I will trade for a hazer.
Bob W2WG
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of Richard (Rick)
Karlquist
Sent: Wednesday, September 27, 2006 10:57 AM
To: Jim Barron; towertalk@contesting.com
Subject: Re: [TowerTalk] Wench for a hazer..??
An easy way to interface the drill to the existing tower winch is to replace
the bolt that holds the winch handle on with the combination of a stud and a
"coupling nut". You can then chuck the appropriate socket wrench socket in
the drill to turn the coupling nut, which will then turn the winch.
In order to prevent the coupling nut from unscrewing when you turn CCW, slip
a box wrench over it and strap the wrench handle to the winch handle. I
modified a cheap box wrench by grinding off the other end and bending the
handle to fit into the winch handle. The cheaper the wrench the better; a
good wrench may not "machine" so easily. The cheap ones can be clamped in a
vise and whacked with a hammer to bend.
("Coupling nuts" are long (1+ inch) hexagonal rods with female threads
intended to couple threaded rod together and should be available in the
threaded rod section of any hardware store.)
Rick N6RK
> -----Original Message-----
> From: towertalk-bounces@contesting.com
> [mailto:towertalk-bounces@contesting.com]On Behalf Of Jim Barron
> Sent: Wednesday, September 27, 2006 6:59 AM
> To: towertalk@contesting.com
> Subject: Re: [TowerTalk] Wench for a hazer..??
>
>
> I think using a worm gear wench with a drill is one easy way And this
> wench will not move without turning the crank (brake or no brake).
>
> I am not sure about 6000# just could be a little large in physical size.
>
> later,
> Jim Barron
>
>
> -----Original Message-----
> From: towertalk-bounces@contesting.com
> [mailto:towertalk-bounces@contesting.com] On Behalf Of J. Gordon
> Beattie, Jr., W2TTT
> Sent: Wednesday, September 27, 2006 8:38 AM
> To: 'Bill Winkis'; towertalk@contesting.com
> Subject: Re: [TowerTalk] Wench for a hazer..??
>
> I'm really daunted by the thought of the 2000# and 6000# "wenches".
> I'm also disturbed by the application of 12V TO THEM and all the talk
> about legs, mounting and sitting on plates. I also totally befuddled
> about the trolley and the relationship of any of this to 45G!
> Finally, I never liked bullying, so I can sympathize with your fatigue
> in "cranking the hazer up the 25G tower". Keep up the good work!
> :-)
> Vy 73,
> Gordon Beattie, W2TTT
> 201.314.6964
> w2ttt@att.net
> w2ttt@att.com
> w2ttt@arrl.net
>
> -----Original Message-----
> From: towertalk-bounces@contesting.com
> [mailto:towertalk-bounces@contesting.com] On Behalf Of Bill Winkis
> Sent: Tuesday, September 26, 2006 5:46 PM
> To: towertalk@contesting.com
> Subject: [TowerTalk] Wench for a hazer..??
>
> I'm tired of crankng the hazer up the 25G tower.....I'm ready for a 12
> volt wench...somebody posted a 2000 pound unit here the other day..but
> the same company offers a 6K unit also..but where and how would you
> mount it, on the legs..or build a plate for it to sit on....
> The other day also a post was made regarding a trolley for a 45G but
> did not see any follow up.....
>
> -Bill
> KC4PE
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|