It was a Hilti but I did not take note of the model, the four hour rental
was $36.00 before tax and required 10% tool protection plan. It was the
mid-size of the three they had. To go into "hammer" mode on yours is the
gear box lever placed in the vertical position? If so this drill was
defective as the other two positions engaged CW and CCW rotation but no
hammering or vibration.
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of K3GM
Sent: Wednesday, August 30, 2006 7:09 PM
To: w0uce@nc.rr.com; towertalk@contesting.com
Subject: Re: [TowerTalk] Dismal Ground Rod / Hammer Drill Results Today
Sorry to hear about the poor results, Jack. You didn't mention what brand
or model drill you were renting. For hammering ground rods, I'd recommend
something like a Hilti TE-74 or TE-76. Hilti is top drawer, and I know our
Home Depot rents them up here. A TE-76 is one BIG hammer drill and unless
you use it on a regular basis, it's not cost effective to own as it's runs
well over a grand.. I own a TE-5, and it will hammer thru my 12" concrete
basement walls like proverbial butter. Hilti makes a special ground rod
driver bit and fits the TE-76 in particular drills. You may have very well
hit ledge, and getting thru that's another story. I think this was a case
of using the wrong tool. You shouldn't have had to chuck up the ground rod,
and it shouldn't have spun like a bit. Give it another try with the right
equipment.
7 3,
Tom Hybiske, K3GM
----- Original Message -----
From: "J A Ritter" <w0uce@nc.rr.com>
To: <towertalk@contesting.com>
Sent: Wednesday, August 30, 2006 4:33 PM
Subject: [TowerTalk] Dismal Ground Rod / Hammer Drill Results Today
With twelve rods to put in I rented a large Hammer Drill from Home Depot
today. They did not have any attachment to use with ground rods but the
clerk said I could simply insert the end of the rod into the chuck and
hammer away.
Being an old timer... I enlisted the help of a strappin tall, in shape local
ham and we set out to "hammer" in 12 ground rods. What a frustrating
experience it turned out to be...
The Hammer Drill did not hammer - all it did was turn like a normal heavy
duty drill. No matter which setting the drill was set on the results were
(1) the chuck turned clockwise (2) the chuck turned counterclockwise or (3)
the drill ran but the chuck did not turn. There was no hammer or vibration
anything other than right or left torque.
The best we could achieve was getting three rods "twisted/pushed" in then
the drill slowed to a crawl with 3' of rod remaining out of the ground on
all 3 attempts. Every attempt the chuck grabbed the rod and it was all we
could do to get the darn drill off the rod, we finally gave up.
Either we didn't have a clue what we were doing or the drill did not work or
both. $36.00 rental fee later, plus two trips to get and return the drill
and the results were dismal. Hammer drills may work in other locations but
certainly did not in NC clay covered by topsoil at my QTH...
Can anyone tell us from experience what the three position selector lever is
supposed to do and do hammer drills really work if a ground rod attachment
is used and the operators know what they are doing?
Thanks,
Jack W0UCE
Raleigh, NC
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|