I use some lmr-600
But I cheated...
I took it to a local company that does commercial work and had them install
the connectors (they did if for free) they are used to working with
hard-line and when I told them That I was using it for a ham radio it really
blew there socks off....
lmr-600 is a bit of an over kill after all
----- Original Message -----
From: "JamesMNelson" <james_junk_mail@comcast.net>
To: <TOWERTALK@contesting.com>
Sent: Friday, December 09, 2005 9:57 AM
Subject: Re: [TowerTalk] LMR- 600 Ultraflex
>
> That is them. I just did not have the time that day to look through the
web
> site. Check out:
>
> Tessco Dissipation
>
> 46450 Times Microwave ST-600C for ""SOLDER"" on connectors
> 14300 Times Microwave ST-600EZ for ""CRIMP"" on connecters
>
> I have one of these tools (ST-400EZ) for 400 and we use the two piece
crimp
> on with out any problems. I work for a national "WIRELESS" company (No
> Names) in the 800 E-SMR band (should give it away), we use these all of
the
> time with out any complaints. Other than the RG-142 they are the easiest
> connectors that I have to put on. Cut end off smooth, slide the ferrule
on,
> prep the cable, slide the connector on, crimp the ferrule. You are done.
One
> min tops when you get use to it.
>
> Good luck and I hope that this helps.
>
>
>
> james//
>
>
> -----Original Message-----
> From: towertalk-bounces@contesting.com
> [mailto:towertalk-bounces@contesting.com] On Behalf Of Jim Smith
> Sent: Friday, December 09, 2005 12:54 AM
> To: TOWERTALK@contesting.com
> Subject: Re: [TowerTalk] LMR- 600 Ultraflex
>
> I think what James is referring to may be found at
>
http://www.tessco.com/products/displayProducts.do?groupId=576&subgroupId=25
>
> HTH, Jim VE7FO
>
> JamesMNelson wrote:
>
> >Bill,
> >
> > As I remember LMR600 is not much different than LMR400. If I remember
> >correctly, the only big difference is that LMR600s dielectric is a little
> >bit thicker; therefore the cable itself is a little bit larger. I have
not
> >had any problems working with it that I recall. It has been a couple of
> >years so my memory is a little foggy. As I remember tessco sells a tool
> that
> >makes the job a breeze. It is a little silver looking tube. There are
> blades
> >on each end. One end takes off the urethane and the other cuts the
shield,
> >dielectric, and champs the center pin. Check them out a www.tessco.com. I
> >hope that this is helpful and if I can help farther please let me know.
> >
> >
> >Thanks,
> >
> >
> >james//
> >
> >
> >James M. Nelson
> >KE4GWW
> >ke4gww@arrl.net
> >
> >
> >
> >
> >
>
> _______________________________________________
>
> See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
> Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with
any
> questions and ask for Sherman, W2FLA.
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
> See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________
See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless Weather
Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any questions
and ask for Sherman, W2FLA.
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|