Towertalk
[Top] [All Lists]

Re: [TowerTalk] Basement entry

To: towertalk@contesting.com
Subject: Re: [TowerTalk] Basement entry
From: Kenneth Cechura <kcechura@umr.edu>
Date: Thu, 9 Oct 2003 15:19:25 -0500
List-post: <mailto:towertalk@contesting.com>
another option would be (since you're planning on running the PVC through 
the wall, i would guess) to use 2" conduit and a standard feedhead with 
associated drip loops, etc.  We have one of these on the roof of the W0EEE 
station for our tower feed....   works very well!

73
Ken, KC9UMR

On Thu, Oct 09, 2003 at 01:53:44PM -0400, Bgsalesmel@cs.com wrote:
> snip..
> To: towertalk@contesting.com
> Subject: [TowerTalk] Running coax into the basement
> 
> 
> How are people getting their coax into the shack in
> the basement ?? i was thinking of using 4" pvc pipe
> with a cap on the outside with holes drilled for coax
> and sealing around each coax run with rtv when i put
> them in ....
> 
> thanks
> 
> Dan N8DCJ
> snip>>>>>
> 
> Dan,
> Do you have daylight windows and is one of them in your operating area?
> 
> I did. After cross connecting all my grounds: Tower base, Cable TV, Elec 
> service, phone to a SPG outside this window - I removed the entire window 
> assy 
> from it's frame. This is in a "dry well" formed by heavy galv steel arch 
> outside 
> the basement wall. Then I made a full size plywood replacement panel, using 
> 1" 
> wood strips outside to "match" the sill to interior ledge depth with some 
> light wt. aluminum channel and long machine screws with wing nuts and fender 
> washers providing the "hold in place" force. I then sawed 2 holes equally 
> spaced 
> in this for 3" PVC. Using a 45 deg ell on both sides, looking down and a 
> "short 
> nipple" between them, I then installed these and just used the force of the 
> setting cement to hold them in place. The entire panel was given 3 coats of 
> Varathene. Each PVC entry was caulked both sides as was the entire edge of 
> the 
> panel once in place. The ells were stuffed with insulation and duct taped on 
> the 
> outside - a natural drip loop was formed when making entry within the dry 
> well. The dry well is protected by a "close" overhang of the upper floor / 
> wall 
> edge. No bugs, no water since the install 3 years ago.
> 
> I use one for my coax and rotor cables and the other PVC for my balanced line 
> alone. I also drilled a 1/4" hole down low on the panel and ran a short #4 
> solid gnd wire to my station ground bar mounted just under this entry window 
> - a 
> 2" x 24" x 1/4" alum bar drilled for PL259 barrel connectors which became my 
> disconnect point for all feeds to the radios themselves. There are arrestors 
> on the coax and bal line outside on the SPG as well. Grounding plugs or 
> straps 
> are used when disconnected - completing the path to gnd for center conductors 
> and rotor wiring.
> 
> Hope this helps.
> 
> 73, de Mel
> KD7DCR
> _______________________________________________
> 
> See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless 
> Weather Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any 
> questions and ask for Sherman, W2FLA.
> 
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________

See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless Weather 
Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any questions 
and ask for Sherman, W2FLA.

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>