N4KG comments inserted in text below
On Wed, 6 Jun 2001 K7GCO@aol.com writes:
> The posts below show the questions that still exist on the need of
> breaking up guy wires.
>
> A single insulator at the tower for all metal guys is a must and
> will > eliminate RF Spill Over transfer to the guys from the tower and
coax
> shield. There can still be RF coupling from the beam to a guy
directly
> underneath even with the insulator at the tower and a resonant length
of a guy
> like an inverted vee. I found minimum coupling with the inverted vees
10'
> or more below the beam.
SNIP
>
> With a 1/2 wave of Phillistran from the tower down to a metal guy
> wire, it's totally out of any field that is of any concern. Scale
this in
> Eznec, rotate > the beam (that will take awhile). and see for your
self.
>
> Further more beams have a vertical directive pattern that points
> straight ahead. Therefore the pattern component pointing down at guy
wires
> is greatly attenuated and any reflected RF is attenuated again back
toward the
> beam.
> The higher the gain of the beam the more isolated the beam is from
> surrounding objects to the side/back and below. It just doesn't see
> them.
OK so far.
> The multiple-insulator installation all the way to the ground is
> mostly just another "TT > Band Aid" for a problem not properly
> addressed like poor feed systems used in beams.
Here's where we disagree. What you say is true for Beams
AT THE TOP of the Tower ONLY. When you side mount other
antennas lower on the tower, then you need insulators on the
guys that pass close to them (within 1/2 WL) as well. For 20M,
this means +/- 35 ft of each side mounted antenna. N4KG
> Fix the source of the problem first. Unless Phillistran is used for
> a 1/2 > wave from the tower I'd suggest an insulator at the tower, one
at
> 5', one at > 15' and one at 30' in metal guys.
As stated before, my preference is to place the first insulator as close
to the tower as possible, typically 3 to 5 ft, depending if torque arms
are used plus the length of two preformed grips. This keeps the
resonance
between insulators, through the tower, and directly under the beam
at the top of the tower well above 28 MHz.
Second and third insulators are then spaced 10 to 12 ft for isolation
on the HF bands. Your 'recommended' 15 ft is VERY close to a 10M
director length...too long for good isolation on 10M.
A real life example of improper top insulator placement was a friend
whose top guys were attached 10 ft below the top of this tower and
the first insulators were 10 ft out from the tower. His tribander worked
fine on 10 and 20 meters, but he felt "less competitive" on 15M where
the guy wires formed a nice 15M director (10 ft + 10 ft + 1 ft thru the
tower) 0.2 WL below the DE of this tribander. Keep that first insulator
CLOSE to the tower !
de Tom N4KG
________________________________________________________________
GET INTERNET ACCESS FROM JUNO!
Juno offers FREE or PREMIUM Internet access for less!
Join Juno today! For your FREE software, visit:
http://dl.www.juno.com/get/tagj.
List Sponsor: Are you thinking about installing a tower this summer? Call us
for information on our fabulous Trylon Titan self-supporting towers - up to
96-feet for less than $2000! at 888-833-3104 <A
HREF="http://www.ChampionRadio.com";>
www.ChampionRadio.com</A>
-----
FAQ on WWW: http://www.contesting.com/FAQ/towertalk
Submissions: towertalk@contesting.com
Administrative requests: towertalk-REQUEST@contesting.com
Problems: owner-towertalk@contesting.com
|