Towertalk
[Top] [All Lists]

[TowerTalk] guys, insulators, etc

To: <towertalk@contesting.com>
Subject: [TowerTalk] guys, insulators, etc
From: n4kg@juno.com (T A RUSSELL)
Date: Sat, 18 Jul 1998 08:57:01 -0600

On Sat, 18 Jul 1998 08:23:42 EDT Mmoon3@aol.com writes:
>
>I have a copy of the Antenna Handbook, but would like to know current 
>trends
>in non-resonant guy lengths.  My guys will be about 55' long.  Should 
>I have
>about 3' at the top, then an insulator, then 14', then 14', then 27', 
>then
>insulator, then anchor?  Is this safe for 14, 21, 28 MHz?

        14 ft is too close to a half-wave on 28 MHz.  I use 12 ft,
        insulator-to-insulator, 2 each, followed by 27 ft. lengths.
        With guy grips, it is best to cut the lengths 1 ft shorter. 
        The first insulator needs to be as close as possible
        to the tower (3 to 4 ft.)  as you are planning.   N4KG
>
>Does everyone use 504 insulators, or 502?  I can get 504's from my 
>local electrical supplier for only $4.55 each.   I will be using 1/4"
guy 
>wire. 

        The large (fist size) insulators should be used with 1/4 inch
        guy wire.
         
>Should I use "genuine" Rohn 1/4CCF clamps (forged, hot dipped) or are 
>the malleable ones OK?

        AARGH!  Most people have gone to using "guy grips",
        actually called "dead-end's"  in the industry.  They
        can be purchased individually from Texas Towers or
        boxes of 50 (for 1/4 inch) or 100 (for 3/16 inch) from
        Preformed Line Products Company in Cleveland, OH.
        I have seen two towers fall over where guys pulled
        through cable clamps that have worked loose.  In both
        cases, I believe there were only two clamps installed
        and the cable was not "served" as shown in the Rohn
        catalog.  Serving 1/4 inch cable is a royal pain.  Cable
        clamps can work loose with time and need to be 
        inspected / retightened on an annual basis.  Go back
        and forth between the nuts as the first one will loosen
        when the second is tightened.  Just this year at Field Day
        I found a loose clamp and the guy informed me he had
        tightened them with a wrench.  Obviously he did not go
        back to the first nut.  If you insist on using clamps, be 
        sure to use good quality galvanized clamps, 3 each.

        Guy grips are a snap and cost effective.  My guy grips 
        and 1/4 inch cable held up two 70 ft trees which fell on 
        them following a small tornado.   Enough said?   N4KG   

>
>Thanks, 73,
>Mark N3AVA/0
>

_____________________________________________________________________
You don't need to buy Internet access to use free Internet e-mail.
Get completely free e-mail from Juno at http://www.juno.com
Or call Juno at (800) 654-JUNO [654-5866]

--
FAQ on WWW:               http://www.contesting.com/towertalkfaq.html
Submissions:              towertalk@contesting.com
Administrative requests:  towertalk-REQUEST@contesting.com
Problems:                 owner-towertalk@contesting.com
Search:                   http://www.contesting.com/km9p/search.htm


<Prev in Thread] Current Thread [Next in Thread>