Topband
[Top] [All Lists]

Re: Topband: Inverted L improvement question - Part 2

To: "'Guy Olinger K2AV'" <k2av.guy@gmail.com>
Subject: Re: Topband: Inverted L improvement question - Part 2
From: "chet moore" <chetmoore@cox.net>
Date: Sat, 5 Jan 2019 14:42:59 -0500
List-post: <mailto:topband@contesting.com>
Hi Guy

Disclaimer noted. That hoarding gene is much more common than most people
think  I had an SB101, SB-200. the SB101 is gone but the  SB 200 and 2 Drake
R4C's and T4Xc's are Still in residence.

My mp 1000 was indeed used at high power multi ops.  Mine was one of the 5
We used at every cq ww cw and SSB and Arrl CW and SSB contest up at W3PP
from
1995 until Dallas perished in that plane crash when taking off from
Charleston S C.  I was supposed to be on that plane which crashed leaving
Charleston SC for Florida and out to C6. After weeks of planning I had to
cancel out the day before the flight. 


I bought my MP-1000 new after using the MP's at W3PP it has the clix mod in
it courtesy of W3PP who spent a full day putting the mod
In all of 4 of his. It has just come back after being gone over by Byron
wa4geg,  I didn't know to have him check the choke but he did install the
new solid state freq readout and a new CAT board. It has every filter that
will fit In it including the w2jvn roofing filter.

I Have Known howie NY4A from when he was K4PQL and when his BIG antenna was
a TA-33 in a tree and all he had was wires through the woods. It sure wasnt
his qth in Lorton va that gave him a good signal as he was basically located
in a gulch.  We used to ride together to the PVRC meetings at the red
Cross building in Arlington Va. he was one of our main ops when I ran the
operation at K4CG along with Dallas K3WUW who later picked up W3PP.  Dallas
and I both worked for Vic Clark W4KFC. When I lived in Dale city, Howie was
the one who climbed the trees in my back yard to put up My 80 m dipole and
160m inverted vee. I climbed my own tower  as well as towers at W3PP but
trees......not so much.

As for K3-s  I operated 2 dx contests at NR4M.  I'm not a big 80M  op and I
planned to operate 10 or 15M because you almost need to go to a 1 week
school
To learn BIP, BOP and which antenna to use at what time of day with those 20
m stacks.  As it turns out the 80M op didn't  show up so they asked if I
Would fill the chair until the 80m  op came in. What a sweet setup. this was
4 or 5 years back but my first time with actual"hands on" a k3.  Actually,
there were 2 of them on 80M And the antennas were if I remember correctly a
5 or 6 element delta loop fixed on EU and a 4 square.  Diversity was turned
on and I had 3501 from the start Of the contest until my eyes slammed shut
around 0600 local the next morning as the 80m op never showed up.  I have
never heard anything like it, it was more akin to 20 meters. Big runs and
EU was loud. My only issue with the  K3's was what I considered  to be the
small knobs. I prefer big knobs on women and radios.  I attributed The high
performance on 80 to be the antennas not the radios. Who knew??  I was so
beat after 12 or 13 hours on 80 that  I slept  until about 3 In the
afternoon. I thought I might get on 160M the second night at NR4M but W4DR
and w4PRO were there. Compared to them  I cant even spell  "160",  I just
watched how the pro's do it. I never did get On 15 or 20. Visitor
accommodations at NR4M  with a pool table and a quiet place to sleep were
like a 5 star hotel compared to the Spartan conditions in the  bunkroom at
W3PP.As dallas would say, I hope you didn't come all this way to sleep.  the
diversity in the K3's was amazing.  I never gave any thought to the 1000 MP
until you mentioned the issues noted below. I will probably never look at my
MP-1000 the same again.  As you may know "CHAMPIONS ADJUST". I realize that
there are now other radios that are better than the MP-1000and I have been
very interested in K3ZO's reports on the Yaesu 5000, even though Fred
doesn't need filters, I do. I think there is at least One yaesu 5000 at
W3LPL  I would definitely want 250 and 500 cycle filters on any radio I
purchase. I  Have not done any multi op since NR4M except for SS CW when my
brother NW9X comes up here for SS.  I was thinking my 160m issues were
antenna related but now that's in question.  I will definitely  try to bring
my MP-1000 to a location with known good Antennas and a K3. It's still true
that no matter how much power you have,  if you can't hear em,  you can't
work em.

I read all your posts and recently discussed your FCP with Lar K7SV who
recently built one. 

Thanks  Guy I appreciate you  taking the time to bring me up to date.

73

Chet N4FX


-----Original Message-----
From: Topband [mailto:topband-bounces@contesting.com] On Behalf Of Guy
Olinger K2AV
Sent: Sunday, December 30, 2018 11:32 PM
To: chet moore
Cc: TopBand List
Subject: Re: Topband: Inverted L improvement question - Part 2

Hi Chet,

Before we start, a disclaimer: I still have my MP, maybe I'm a radio
hoarder. I do have a 75A3 and a Johnson Ranger and Courier and an FT 101ZD.
The only long used radios I don't still have are my SB300 and SB400, and I
wish I hadn't sold those. So my MP bashing is technical and proven, and I
still love my MP enough to keep it. I hope its feelings aren't hurt by lack
of use since the K3.

Back in the heyday of FT1000MP, when that was one of the best contest
radios available (IF you fixed the clicks), I used to take mine out to N4AF
for the multi-op DX wars as NY4A. I used my MP on 40 meters out there,
which at that time was listening to a 5 element quad stretched out on 190
feet of catenary between towers, end-on to 45 degrees. Loads of incoming RF
off the big quad.

With the MP, the bottom layer of signals was usually all the DL/OK basement
noodle antenna QRP signals. When the K3 showed up, the DL/OK basement
noodle QRP crowd became essentially workable and the new bottom layer of
signals was all the European Russians running 100 watts to a dipole up 20
feet on the southeast side of a big hill.  Goaded by the astonishing
improvement, some K3 to MP comparisons showed very convincingly that what
we always thought was the bottom atmospheric level in the MP was actually
being generated IN the MP, because it was absent in the K3. A/B there, not
there, couldn't possibly be that much. Repeat test 50 times at least,
there, not there. After a half hour of doing the same test over and over,
with exact same result over and over, "Gee, guess the K3 has improved a
lot."

N4AF switched to K3's, and very quickly all the "drug-in-with" radios were
K3's, except for one Orion I. Within a couple years, 11 FT1000MP's in the
NY4A crowd morphed into 14 K3's.

There definitely WERE some separate sensitivity issues in the MP, a bunch
caused by too much RF coming in the line in RX mode. Your deaf as a
door-nail kind of spot reports screams as a repeat of one of those MP
insensitivities.

There is a little itty-bitty choke in the RX on TX antenna circuit, which
can burn but NOT GO OPEN. It goes resistive because what's left over after
the wire burn is still conductive. The DEGREE of resistive is unpredictable
and can change. I know because over the years I've replaced a half dozen of
them. You can find them in the schematic. The quick no-solder,
no-disassembly fix to get around the problem and listen on the TX antenna
with full sensitivity is 1) on the back panel patch the RX OUT RCA jack
(connected to TX ant when not transmitting) to RX IN RCA jack right next to
it, and 2) on the front panel use ANT RX. The coil is not in the RX ANT
circuit. If you suddenly hear better, you know what to do. If you never do
SO2R or operate the MP at a multi transmitter site, you maybe don't need
the choke. The K3 has a COR relay for this.

We always replaced the @%#@^&!! chokes because we were afraid to run the
MPs at the multi site without those as protection for some cross-antenna
backfeed we had unknowingly reintroduced.

I can't explain the MP engineering there. That's just how it is.

If you bought the MP second-hand and in its other life it was operated at
high power multi sites, it could have been that way since you had it,
therefore no suddenly worse performance as a clue to check things out.

Anyway, I would check that out before you go tearing up all your antennas.

73 & HNY all,

Guy K2AV

On Sun, Dec 30, 2018 at 8:35 PM chet moore <chetmoore@cox.net> wrote:

> Todd,
>
> Thanks for sharing. I've been following your post.  I too wondered about
> sharing the radial field like you did.  My situation is somewhat similar
in
> that I feed a 90 foot tower which has a c31 at 95  feet and a two el xm
240
> 40m beam  at 75 feet beneath it on a gate....the antennas should give me
> some top loading but it has never been modeled.  Shunt wire presently
comes
> down from 70 feet about 3 feet out from the tower to the base of my tower.
> The Tower(AB-105) Is guyed at 40 and 70 feet, guys are broken up with
> insulators. I have tried to find the resonant  freq of the tower  and at
> one
> time or another I have moved that tap from 40 feet to up 50  60 70 feet in
> 2
> foot increments. (that's a lot of climbing)and  never found the sweet spot
> if there is one. I saw your post and  Like you I  wondered what  would
> Happen if I  ran an inverted L up to 90 feet. (I already had a pulley and
> rope up there) and run the tail out to the west since I seem to be "deaf"
> to
> the west and north west (and really everywhere) and would share The same
> radial field which  has 2 radials that I was able to stretch out to 100
> feet
> (in a very crooked line)  and a couple of others  that are 60 feet  and 56
> others  of various lengths from 20 to 50 feet. The correct word is
probably
> not "share" as only one of the antennas would be hooked to the xmtr at a
> time.  My salt water swimming pool Is about 8 feet from the base of the
> tower. Not sure if the pool helps or hurts in any way. In the fall, once I
> cover the pool,I run out 30 radials of varying lengths  which I have to
> roll
> back up again come spring when we uncover the pool.   I remotely tune the
> tower with a motorized vacuum variable capacitor to tune  the tower for
> minimum swr.  I've only played with this since I saw your post.  5 years
> ago
> Before trying the shunt fed tower,  I put up the inverted L with 4 buried
> radials mainly to be able get some points for PVRC in the DX contests.
160m
> has a way of hooking you in to trying to do just a little more than the
> bare
> minimum  I then added 6 more radials,  then  a few more and then a few
more
> after that. I noticed that things got better Up until I had 20 radials or
> so
> and then adding more radials didn't  seem to help or hurt anything .
> Bandwidth went down at first and then like it says in the on4un book,
> leveled out. The real problem for me is RX. I have never heard a KL7 on
160
> even though guys locally  3 or 4 miles away hear and work KL7's in every
> arrl  or cq 160 contest. (I'm located 7 miles off the water at Virginia
> beach)  I have managed 1 KH6 QSO (could not hear either of the two I saw
> spotted last night in the stew)  Things are up and down here. Stuff I
don't
> expect to hear. I sometimes get,  but  other easier stuff I never hear.
> Example,  when I was able to work the ET3 on 160 a while back. I also got
> Yemen when K1ZM  was in sanaa,  I got bouvet last time out,  the last 2
> FT-8's but still no KL7.  Never expected to work the VP6 or whatever the
> latest big dxpedition  was a few weeks ago , the one that  had to leave
> early due to weather. Vp6di Ducie? Xmas? Either one would have been new
one
> for me on 160. I just knew I wouldn't hear them so I did not check for
> them........Until the night before they left,   I turned on the rig, I was
> on 40 m and  saw them spotted. Figured ok I'll waste my time and Clicked
on
> the spot.  I could actually hear them on my 40 m beam,   switched to the
> shunt fed tower and zip, nada, nothing. Back to the 40m beam and they were
> still there.  Went down to feed point and found that  the dogs toy was
> entangled in the shunt feed and in trying to remove it, the dog had ripped
> the feed wire off  of the  top of the vacuum variable with his toy still
> attached.  It was pouring rain so since this expedition was gonna be there
> 2
> more days I figured I'd fix it at first light or as soon as the rain
> stopped
> and be ready that night. I was  WRONG. The weather apparently got so bad
> they left early so I never got to call them.
>
> In the Stew I tried out a couple of quick swap outs between the inverted L
> and the tower on both G4AMT & KV4FZ last night  in the stew when both were
> running em and I could not discern any  difference on receive between the
L
> and the tower. I worked both of them with 100 watts. I called N6RK on both
> antennas. On the inverted L I got an imi, and on the shunt fed tower no
> response. Lots of qrm.  n6rk was not loud but he was the ONLY w6 I heard.
> N2IC was loud from new mexico all night.
>
> When I try to call cq I can hear partial calls and I know there are
> stations
> calling  me. I know I was called by an  EU4, 9A2 and a TF2 last night but
I
> couldn't pull any of them thru.
>
> The shunt fed tower seems to radiate  pretty well on xmit but  on rx its
an
> alligator.  I definitely get out better than I hear but its  still pretty
> discouraging  to call CQ and  to look at dx summit  and
> see.....................spots like these from the europeans
>
>
> N4FX  ZZZZ ?????.
> N4FX  no receiver
> N4fx  don't waste your time calling,  rx broken
> N4FX  No ears
> N4FX  Unmanned beacon station??
> N4FX  Big signal does not hear
> N4fx  code reader failure???
> N4FX  op asleep at key???
> N4fx  where is he listening?? is he even listening?
> N4FX   working crossband???
>
> I have tried a 200 foot BOG which actually runs across the street and cars
> drive over it. (I roll it out after dark but not a busy street). And roll
> it
> back up when I am finished) It works pretty well sometimes but last night
> was not one of those times.  tried a W2UP rotatable Loop which lost all
> directivity when I ran some radials out in its direction. A VE3DO loop (no
> joy at all)
>
> I just had my mp1000 tweaked and have a 756 pro II and don't think either
> of
> them has an rx problem.
>
> Talked to Lee K7TJR about his antennas and because my tower sits almost
> smack dab in the center of my lot  he didn't seem to think it would work
> well even if
> I were to detune the tower.  I'm not sure that a K9AY or SAL would work
for
> the same reasons.
>
> Like you I think I will just take down the inverted L.  I learned quite a
> bit from some of the comments you got. I  didn't fix anything but
> definitely
> know a lot of things that won't work. It was not particularly reassuring
> that when AA1K was here last year, I asked him if he thought a choke at
the
> feed point would help anything?  He said he didn't think one was needed on
> a
> vertical. Then I asked what else I could do he suggested that I might want
> to consider putting up a FOR SALE sign.
>
> Thanks again for sharing your results.
>
> 73
>
>
> Chet      N4FX   KP4EAJ, VP2A, ZD8W, VQ9Xx, KL7AIZ, KG4ZO, N6Zo/HH9
> N6ZO/6Y5
>
>
>
>
>
>
> 
hable Archives: http://www.contesting.com/_topband - Topband Reflector


---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus

_________________
Searchable Archives: http://www.contesting.com/_topband - Topband Reflector

<Prev in Thread] Current Thread [Next in Thread>