Topband
[Top] [All Lists]

Re: Topband: BOG

To: topband@contesting.com
Subject: Re: Topband: BOG
From: Herbert Schoenbohm <herbert.schoenbohm@gmail.com>
Date: Sun, 16 Oct 2016 20:17:29 -0400
List-post: <topband@contesting.com">mailto:topband@contesting.com>
If the far end is left un-terminated the BOG will not work well as I have found here. Try a small ground rod of 4 feet and a 250 ohm resistor and sweep again. I predict your results will be much better.


On 10/16/2016 7:15 PM, Lloyd - N9LB wrote:
Boxbe <https://www.boxbe.com/overview> This message is eligible for Automatic Cleanup! (lloydberg@charter.net) Add cleanup rule <https://www.boxbe.com/popup?url=https%3A%2F%2Fwww.boxbe.com%2Fcleanup%3Fkey%3DfR9iWh5k8xSTPJ8X%252FUYNbJnH%252Bl7Ia8oOLYAqRA1J1Bk%253D%26token%3DAaqJg0%252BHPRHT0xZqU5t87i%252BW2YSKwFV8i6dU6OGE3hL35PAbic5atzh9sdoLjlkCodQFJhTgUkCFlRUsOHLJuju%252BaLyRNKf90SOpNtXgTiEqGw4y0JRcvCCY4YG8hE2kr%252F06omiB%252Fqxhkg%252FHeLAkuQ%253D%253D&tc_serial=27191928583&tc_rand=323842429&utm_source=stf&utm_medium=email&utm_campaign=ANNO_CLEANUP_ADD&utm_content=001> | More info <http://blog.boxbe.com/general/boxbe-automatic-cleanup?tc_serial=27191928583&tc_rand=323842429&utm_source=stf&utm_medium=email&utm_campaign=ANNO_CLEANUP_ADD&utm_content=001>


Hello Tony!

Ground conditions and wire height above ground make a huge difference in
best length.

I found the optimum for my BOG, using WD-1A wire and operating at 1825 KHz,
at my QTH is 290 feet.

73

Lloyd - N9LB

-----Original Message-----
From: Topband [mailto:topband-bounces@contesting.com] On Behalf Of N2TK,
Tony
Sent: Sunday, October 16, 2016 5:15 PM
To: topband@contesting.com
Subject: Topband: BOG

Stretched out 200' of WD-1A along a stone wall. Kept it about 2" above the
ground and right up against the stones. Fed it with a 300 ohm secondary
transformer and left the far end unterminated.

Used the MFJ-259 to sweep the bands starting at 1.67 MHZ.  Saw on K1FZ notes
that to find the best single wire length for 160M is to sweep the bands and
check where the SWR goes to a low value and stays there.

I couldn't find that frequency. I get dips at

2.58 MHZ 4.3:1
3.36 MHZ 1.5:1
4.39 MHZ 1.4:1
6.033 MHZ 1.3:1
9.807 MHZ 1.2:1
I didn't check any higher in freq. I only care about listening on 160M with
it.
I twisted both wires together at the feedpoint.
Want to check it out first as a single ended BOG to see how it works before
I go to the trouble of making it a two direction BOG.
At one point the BOG is only 35' from my tower.
Is it too high and does it need to be against the ground?

Any feedback appreciated.

N2TK, Tony
_________________
Topband Reflector Archives - http://www.contesting.com/_topband

_________________
Topband Reflector Archives - http://www.contesting.com/_topband

_________________
Topband Reflector Archives - http://www.contesting.com/_topband

<Prev in Thread] Current Thread [Next in Thread>