Topband
[Top] [All Lists]

Re: Topband: FT-1000MP

To: Top Band Contesting <topband@contesting.com>, PVRC Submissions <pvrc@mailman.qth.net>
Subject: Re: Topband: FT-1000MP
From: donovanf@starpower.net
Date: Wed, 15 Jun 2016 11:29:49 -0400 (EDT)
List-post: <topband@contesting.com">mailto:topband@contesting.com>
Hi Kip, 


Your question involves perhaps the most frequently misunderstood 
aspect of FT-1000MP receiver operation, a result of the poorly 
written description of Menu 8-4 on page 91 of the operating 
manual . A much better description and illustration of pre-amplifier 
selection menu 8-4 and the IPO front panel push button appears 
on page 30 of the operating manual. 


Two controls must be properly set to optimize FT-1000MP receiver 
front-end performance on 160, 80 and 40 meters: Attenuator and 
IPO. When IPO is enabled, it bypasses the pre-amplifier selected 
by Menu 8-4. 


The FT-1000MP has three pre-amplifiers: 
- a 1.8 - 7 MHz pre-amplifier ( IPO should be enabled when 
operating on 160, 80 and 40 meters to bypass this pre-amplifier) 
- a pre-amplifier with excellent sensitivity on 24 and 28 MHz 
- a wideband ( FLAT ) pre-amplifier with very poor 28 MHz sensitivity 


The front panel IPO pushbutton bypasses the pre-amplifiers entirely, 
feeding the antenna directly into the first mixer. I always enable 
IPO when operating on 160, 80 and 40 meters. 


The Attenuator should be set to the highest setting while providing 
acceptable receiver sensitivity. I almost always set the attenuator 
to 18 dB when operating on 160 meters. 


I always set Menu 8-4 to TUNED , allowing the FT-1000MP to 
automatically select the proper pre-amplifier for 12 and 10 meters, 
I never use the 1,8-7 MHz preamplifier because I always enable 
IPO when operating on those bands and I never set Menu 8-4 to FLAT . 


73 
Frank 
W3LPL 









----- Original Message -----

From: "Kip Edwards" <kedwards@ltol.com> 
To: "Top Band Contesting" <topband@contesting.com> 
Sent: Wednesday, June 15, 2016 2:07:09 PM 
Subject: Topband: FT-1000MP 

All, 



I have been corresponding via email with Andy, SP6AEG, 
regarding the 5J0P DXpedition and other topics. This morning I received the 
following question from Andy: 



"I received from Janusz SP6IXF as gift transceiver FT1000MP with a set of 
filters in optional (2 kHz / 250 Hz) ssb / cw + roofing filter. I have a 
dilemma, do not know who Receiver Front-End RF Amplifier should be active 
for optimal performance for 160 m. I have a choice of flat or Tuned for low 
band. Do you have on this subject some knowledge?" 



Is there anyone on this reflector who can offer any help? I 
know nothing about the 

FT 1000MP (among many other things) but I'd like to help Andy. 



Many thanks. 



73 Kip W6SZN 





G. Kip Edwards 

Telephone: (206) 999-9403 

email: kedwards@ltol.com 



NOTICE: This E-mail (including attachments) is covered by the Electronic 
Communications Privacy Act, 18 U.S.C. 2510-2521, is confidential and may be 
legally privileged. Information contained in this e-mail message is intended 
only for the individual to whom it is addressed and is private and 
confidential. If you are not the intended recipient, or the employee or 
agent responsible for delivering this message to the intended recipient, any 
dissemination, distribution or copying of this communication is strictly 
prohibited. If you are not the intended recipient of this e-mail, please 
kindly destroy it and notify the sender immediately by reply e-mail. Please 
take standard precautions to mitigate virus issues. Thank you for your 
cooperation. 



_________________ 
Topband Reflector Archives - http://www.contesting.com/_topband 

_________________
Topband Reflector Archives - http://www.contesting.com/_topband

<Prev in Thread] Current Thread [Next in Thread>