Topband
[Top] [All Lists]

[TowerTalk] More: Topband: New Antenna

To: <towertalk@contesting.com>, <topband@contesting.com>,<WarrenWolff@aol.com>
Subject: [TowerTalk] More: Topband: New Antenna
From: "DAVID CUTHBERT" <DAVIDNNAN@MSN.COM>
Date: Sun, 26 Dec 2004 19:38:56 -0700
List-post: <mailto:towertalk@contesting.com>
Warren,

I thought I had better really the flagpole rather than just dismiss it out of 
hand. Here are some possibilities:

1) wire from the top of 35' flag pole to the tower, at the 35' level. Rr = 7 
ohms
2) wire from the top of the 35' pole towards the top of the tower. Rr = 16 ohms 
3) wire from the top of the 70' tower (not attached to the tower) towards the 
top of the 35' pole. Rr = 16 ohms
4) wire connected to the top of the 70' tower towards the top of the 35' pole. 
Rr = 17 ohms
5) tower feed. 16 ohms. 
6) top load the 70' tower with a coil and a top hat or spike. Rr = 25 ohms.

Number looks bad. Scratch that one. Number 2-5 all look good from a performance 
standpoint. Number 2 looks to be the simplest to implement. This can be fed 
directly with 50 ohm coax and tweaked with a good tuner at the shack. This is 
the one I would seriously consider. Number 6 has the highest performance IF 
your ground system is not very good. You get 9 ohms more Rr at the expense of a 
few ohms of top loading coil loss. This one needs shunt feeding of the tower 
and is a lot more complicated to get going than number 2. 

These sims are subject to having better inputs (dimensions, ground, radials, 
etc.) but I believe them to be good for comparison of the different designs. 
None of these, except for number 6,  requires loading coils. All of the rest 
are adjusted to resonance by the length of the horizontal wire. 


     Dave  WX7G


  ----- Original Message ----- 
  From: WarrenWolff@aol.com<mailto:WarrenWolff@aol.com> 
  To: towertalk@contesting.com<mailto:towertalk@contesting.com> ; 
topband@contesting.com<mailto:topband@contesting.com> 
  Sent: Sunday, December 26, 2004 12:29 PM
  Subject: Topband: New Antenna


  Greetings,
   
  I have a question about choices on 160 meters.
   
  I expect to have a new home at Lake Havasu City next  summer.
  I will have a 60/70 foot fixed tower topped by a couple of  OptiBeams
  (16-4 and a 4-40).
   
  About 100 feet away, I expect to have a 30/35 foot flag  pole.
   
  What is my best way to get on 160 with this arrangement?   A couple
  of ideas come to mind.
   
       1)   Shunt feed the  tower
  2)   Use a wire between the top of  the tower and the top of  the
  flagpole  to use as top loading for vertical wire in the  center
  of  it.
  3)   Extend an arm out from the top of  the tower, say around  6-8
  feet and  drop some kind of vertical element to be base-fed.
   
  Advice is needed; please donât say I am nuts.
   

  Warren; W5KKW
  _______________________________________________
  Topband mailing list
  Topband@contesting.com<mailto:Topband@contesting.com>
  
http://lists.contesting.com/mailman/listinfo/topband<http://lists.contesting.com/mailman/listinfo/topband>
_______________________________________________

See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless Weather 
Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any questions 
and ask for Sherman, W2FLA.

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>