TenTec
[Top] [All Lists]

Re: [TenTec] Eagle & Heath SB-200 Amp

To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Subject: Re: [TenTec] Eagle & Heath SB-200 Amp
From: <Rick@dj0ip.de>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 25 Feb 2020 23:55:33 +0100
List-post: <mailto:tentec@contesting.com>
The problem with using an external relay is, it adds additional latency to the 
scenario, and there is already a timing issue with it on CW.

The very best solution is to replace the SB-200's internal relay with a 12v 
relay.  Then there is no additional delay added to the switching.   There are 
kits on the market for doing this.

ALSO, the 17mS pre-dit delay that Bob spoke of requires the very latest 
firmware release.  Otherwise the delay is only about 7 or 8mS.  (Originally it 
was 17mS from the factory, but it got screwed up in later firmware releases and 
wasn't fixed until about a year ago.)

73,
Rick, DJ0IP
(Nr. Frankfurt, Germany)
May the Sunspots be with us!

-----Original Message-----
From: TenTec <tentec-bounces+rick=dj0ip.de@contesting.com> On Behalf Of Rodney 
Dewald via TenTec
Sent: 25 February 2020 23:48
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Cc: Rodney Dewald <w3krq@ptd.net>
Subject: Re: [TenTec] Eagle & Heath SB-200 Amp

I have used a 12vdc relay and use the contacts to switch the 120v

Sent from Mail for Windows 10

From: Rick@dj0ip.de
Sent: Tuesday, February 25, 2020 5:41 PM
To: 'Discussion of Ten-Tec Equipment'
Subject: Re: [TenTec] Eagle & Heath SB-200 Amp

Actually there are various kits for installing inside of the SB-200 that 
present a 12v keying circuit.
That's why I said he needs to tell us exactly how the amp has been modified, 
with circuit drawing.

I don't recall all of the names and sources; one was called a soft key, and 
used solid state keying that could handle the 120 volts, yet presents 12v to 
the transceiver.

That's why I also said STOP, DON'T DO ANYTHING . . . until we find out.
Otherwise there will be an expensive repair to the Eagle.

73,
Rick, DJ0IP
(Nr. Frankfurt, Germany)
May the Sunspots be with us!

-----Original Message-----
From: TenTec <tentec-bounces+rick=dj0ip.de@contesting.com> On Behalf Of Bob 
McGraw K4TAX
Sent: 25 February 2020 17:40
To: tentec@contesting.com
Subject: Re: [TenTec] Eagle & Heath SB-200 Amp

WOAH!    STOP!    If the amp has not been modified for the KEY circuit, it has 
120 volts on the center pin of the RCA connector.   If this is connected to the 
Eagle it will immediately destroy the Eagle PTT Amp control circuit.

The amp relay must be changed to a 12 volt relay and other circuit 
modifications done,  OR you must use an Amp Interface between the radio and the 
amp.

Who ever gave you the information DOES NOT know what they are talking about.   
This is normal for most hams unless they have actually interfaced the SB-200 to 
the Eagle.    MFJ did make an interface suitable for the application.

As Will Rogers said: "it's not what people know that concerns me, it is what 
they know that is not correct that gives me concerns".

If you need additional information, I'll be glad to assist.

73

Bob, K4TAX


On 2/25/2020 8:13 AM, Richard Wagner via TenTec wrote:
> I’ve never dealt with an Amplifier before. A friend gave me a Heath SB-200. 
> It appears I have to make a connection between the AMP KEY terminal of the 
> ACC-1 accessory connector and the AMP KEY Socket of the amp. A plug for the 
> socket and short jumper wire were included with my Eagle. This appears to be 
> all that is needed. I’ll connect from the Eagle to the Amp then through my 
> Antenna Tuner to the Antenna. Does this seem OK?
>
> Rich Wagner
> K4MZE
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
<Prev in Thread] Current Thread [Next in Thread>