TenTec
[Top] [All Lists]

Re: [TenTec] Version 3.033xd July 9, 2013

To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Subject: Re: [TenTec] Version 3.033xd July 9, 2013
From: <pa5mw@home.nl>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 13 Aug 2019 16:25:31 +0200
List-post: <mailto:tentec@contesting.com>
Original supplied 'How to' yxt file:

pdating the FLASH FIRMWARE on Ten-Tec Orion

Refer to "74474 Orion565n566 User Manual Addendum V3 Firmware.pdf"
for more details on Version 3 firmware, and the RAM Clear and Master Reset
sequences.

1) Turn Transceiver OFF.
2) Connect a PC to the transceiver using the appropriate cable.
3) Turn the Transceiver ON while holding down the USER2 button.
   Wait for display to indicate "Flash Update Mode"
4) Start the Update program
    Windows "START"
        "All Programs"
        "Ten-Tec"
        "OrionII Firmware Update"
        "OrionII Firmware Update"
5) Choose SETUP under the SETTINGS menu to then select the COM port 
   to which the Transceiver is attached. And select OK.
6) Choose UPDATE under the PROCESS menu.
7) Select the RUF file under the Process Menu.
8) The program will update the radio and report any errors encountered. 
   During the update process the Orion screen will indicate the current 
   line being processed.
9) A RAM Clear and Master Reset MUST be performed when transitioning between

   V1/V2/V3 firmware.

-----Original Message-----
From: TenTec <tentec-bounces@contesting.com> On Behalf Of Petr Ourednik
Sent: Tuesday, August 13, 2019 15:18 PM
To: pa5mw@home.nl; 'Discussion of Ten-Tec Equipment' <tentec@contesting.com>
Subject: Re: [TenTec] Version 3.033xd July 9, 2013


73 Mark PA5MW




Mark,

again many thank.
Just small question > in case of 3.033xd revision do I need also to make
Master reset and RAM clearance after the fw upgrade as it is requested for
latest 3.033xe revision please?

Petr OK1RP

On Tue, Aug 13, 2019, at 1:30 PM, pa5mw@home.nl wrote:
> Hi Petr,
> 
> Plse find attached  file
> 
> 
> 
> 73
> Mark
> PA5MW
> 
> 
> -----Original Message-----
> From: TenTec <tentec-bounces@contesting.com> On Behalf Of Petr 
> Ourednik
> Sent: Tuesday, August 13, 2019 10:56 AM
> To: tentec@contesting.com
> Subject: [TenTec] Version 3.033xd July 9, 2013
> 
> Hi folks,
> 
> is there some nice guy to send me the fw Version 3.033xd July 9, 2013 
> file for Orion II please?
> I did not find it anywhere to download...
> (on the TT web is the 33xa ver. instead in the "xd" folder)
> 
> Many thanks,
> 
> 73 - Petr, OK1RP
> --
> Omni V.4, Orion II
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 
> Attachments:
> * 566-Setup-3.033xd.exe

--
73 - Petr, OK1RP
--
B: http://goo.gl/Fd2JhJ
MeWe: https://bit.ly/2HGPoDx
MeWe: https://bit.ly/2FmwvDt
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>