Hi Carl thanks!!!yes I own your software for both my Orion 2 and my 2 K3
radios, pegaus software for those, I am the guy u helped eliminate the
sluggishnish I was having using the Flex control with the pegasus software and
my K3 radios,,, so I will read the manual lol I never saw it in rhere,, also I
am adding the IF mood to my Orion to hook up the Lpan unit which I am preety
sure your orion software supports!!! All these mods started because I tore
radio apart and am changing all the encoders on the encoder board,, ugh not fun
but since its apart I wanted to do the mods! Thanks for the heads up on ur
info,, ands since its so simple I am going to use the spare jack for IF mod,,
and use a small RF type BNC relay mounted in the radio so I can still use Ant 2
with the sub of flip the relay and have an external receive antenna jack
avaible for thw sub. ,,,
Thanks again for the info its turning out to be way easier than I thought,
Tom
N7GP
Ex wa8wzg
73
Tom
-----Original Message-----
From: Carl Moreschi <n4py3@earthlink.net>
Sender: "TenTec" <tentec-bounces@contesting.com>Date: Thu, 28 Feb 2019 19:20:55
To: Discussion of Ten-Tec Equipment<tentec@contesting.com>
Reply-To: n4py3@earthlink.net,
Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Orion 2 SUB receiver Question
You can also just run a small rg174 coax from the sub-receiver antenna
connection to the spare jack. Then select no antenna at all for the sub
and connect an antenna for the sub to the spare jack.
This is exactly how I use an SDRplay as a panadapter with my Orion.
I have this written up in the manual for my N4PY Orion software. You
can download this manual from my website at n4py.com
73,
Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com
On 2/28/2019 6:53 PM, wa8wzg@wa8wzg.net wrote:
> Thans Carl,, Looking at it now,,
> Thanks
> Tom
> N7gp
> ex WA8WZG
>
>
> On 2019-02-28 16:13, Carl Moreschi wrote:
>> The antenna connection to the sub-receiver is very obvious when you
>> look at the sub-receiver. You can pull the connector and put another
>> on there that goes to the spare jack in the back. That will do it.
>>
>> 73,
>>
>> Carl Moreschi N4PY
>> 58 Hogwood Rd
>> Louisburg, NC 27549
>> www.n4py.com
>>
>> On 2/28/2019 3:38 PM, wa8wzg@wa8wzg.net wrote:
>>> Does anyone have a Mod or even a thought of a way to add a second
>>> RECEIVE only port for the Sub receiver,.On an Orion 2,. at present I can
>>> only use Ant 2 to select a diversity receive antenna to the SUB
>>> receiver..but was wanting to use antenna 2 for another antenna on a
>>> different band ,so dont want to tie up Antenna 2 jack for diversity
>>> receive.
>>> I dont care if any mod would allow the sub receiver to only have the
>>> separate receive port,, I only use sub receiver for diversity..
>>> Any thoughts would be appreciated..
>>> Thanks
>>> Tom
>>> N7GP
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|