TenTec
[Top] [All Lists]

Re: [TenTec] notch filter for Eagle?

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] notch filter for Eagle?
From: Gary F <dukeshifi@comcast.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Wed, 19 Jul 2017 20:36:11 -0500
List-post: <mailto:tentec@contesting.com>
Agreed in principle...

I use a Pro 2, nowhere near the performance level of an Eagle or Orion. It has 
the digiwidji auto notch, useless as any notch outside the AGC loop is. 
However, its manual notch is truly manual, and very effective without desensing 
the receiver. This makes it every bit as useful as the old fashioned Q 
multiplier notch filters like the Drake receivers and Collins receivers had.

That is the primary reason I don't have either an Eagle or Orion.

For a few years, Ten Tec did promise to put the notch filter inside the Orion 
AGC loop but never did. It must have been harder to do than expected.
Gary
Sent from my iPad

> On Jul 19, 2017, at 8:16 PM, Greg S via TenTec <tentec@contesting.com> wrote:
> 
> 
> 
> 
> Yup. One reason I sold my Eagle. Auto notches are fine, but I prefer both 
> auto AND manual, with the ability to have both engaged simultaneously. 
> Everyone has their druthers.
> 
> Greg, KC8HXO  
> 
> 
> 
> 
> 
> 
> 
>> 
>> On Jul 19, 2017 at 20:58,  <Michael Tortorella (mailto:w2iy@verizon.net)>  
>> wrote:
>> 
>> 
>> 
>> My manual says auto-notch does not operate in FM or CW :( -----Original 
>> Message----- From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf 
>> Of P C Andy Anderson Sent: Wednesday, July 19, 2017 5:44 PM To: Discussion 
>> of Ten-Tec Equipment Subject: Re: [TenTec] notch filter for Eagle? Look at 
>> 2.2 SSB Operation AN (8). Page 14 in my manual. Andy W3LI 
>> ________________________________ From: TenTec on behalf of Gary F Sent: 
>> Wednesday, July 19, 2017 5:33 PM To: w2iy@verizon.net; Discussion of Ten-Tec 
>> Equipment Subject: Re: [TenTec] notch filter for Eagle? The Eagle does have 
>> a notch function. I don't recall how to activate it but it is in the manual. 
>> It's sort of useless, like all Ten Tec notch filters, since it is outside 
>> the AGC loop, so, while it does not have the carrier, it also attenuated 
>> your desired signal by about as much as it reduces the carrier. The 
>> reduction to 20 watts in Tune is self-defense. Orion's do it too. This is to 
>> prevent the presence of full 100 watts
>   into a
> mismatch. It is good policy. Orion's had an option in which you could press 
> the Power button, I believe, to get 100 watts in Tune after match had been 
> reached. Red arid green the A//B VFO, there really is no A or B VFO in the 
> traditional sense and Eagle only has one tuning knob. Therefore, the A/B 
> indicator serves no function in transceive operation. In split operation, 
> that indicator should flip when going fro RX to TX to tell you which 
> displayed frequency is the TX frequency. Gary Sent from my iPad  >  On Jul 
> 19, 2017, at 3:05 PM, Michael Tortorella wrote:  >   >  Hi all, I am hearing 
> an awful lot of steady carrier signals up here in the  >  frozen north of 
> Downeast Maine. Most are not very strong and they go away  >  when I 
> disconnect the antenna so they are external to the radio. Today I am  >  
> chasing TR8CA on 20 CW, he is way down in the noise, and 100 Hz away from  >  
> one of these carriers. Sure would be nice to have something like a notch  >  
> filter to help in situa
 t
> ions lik
> e these but I could not see anywhere in the  >  manual or front panel where I 
> could notch the offending carrier. Is there  >  any list wisdom on this?  >   
> >   >   >  On another note, I did contact service at TT last week with my 
> question  >  about power out in autotune; after only a few days delay I got 
> an answer  >  that the power out in autotune is 20 watts even though the 
> power output  >  shown on the display is 100. This seems not quite right from 
> a human  >  factors point of view, maybe there can be a firmware fix? Also, 
> when  >  exchanging VFOs, the A,B labels do not change even when the B vfo is 
> in  >  large type at the top of the display. I find this confusing. OK, I 
> guess  >  this turned into a longer letter about a couple of other things 
> besides  >  notch filtering, so please excuse my prolixity and thank for the 
> BW. Any  >  suggestions appreciated.  >   >  Thanks and 73, Mike W2IY  >   >  
>  >   >  ---  >  This email has been checked for viruses by AVG.  >  http:/
 /w
> ww.avg.c
> om AVG 2017 | FREE Antivirus  &  TuneUp for PC, Mac, Android www.avg.com 
> Download FREE antivirus and malware protection. Tune up your PC, Mac and 
> Android devices for peak performance. Surf safely and privately, wherever you 
> are.  >  _______________________________________________  >  TenTec mailing 
> list  >  TenTec@contesting.com  >  
> http://lists.contesting.com/mailman/listinfo/tentec TenTec Info Page - 
> Contesting lists.contesting.com Your email address: Your name (optional): You 
> may enter a privacy password below. This provides only mild security, but 
> should prevent others from messing ... 
> _______________________________________________ TenTec mailing list 
> TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec 
> TenTec Info Page - Contesting lists.contesting.com Your email address: Your 
> name (optional): You may enter a privacy password below. This provides only 
> mild security, but should prevent others from messing ... 
> _______________________________________
 __
> ______ T
> enTec mailing list TenTec@contesting.com 
> http://lists.contesting.com/mailman/listinfo/tentec 
> _______________________________________________ TenTec mailing list 
> TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec 
>> 
>> 
> 
> 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>