TenTec
[Top] [All Lists]

Re: [TenTec] Ten Tec Eagle com3 problem

To: w2iy@verizon.net, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Ten Tec Eagle com3 problem
From: Mark killen <markkd8qig@gmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 18 Jul 2017 10:42:51 -0400
List-post: <mailto:tentec@contesting.com>
Thanks mike, I'll try.  Did you try to hold down the tune button?  When I
do that it switches to 20 watts.  Just hit the tune button again and then
it will work.  At least it does mine!



On Tue, Jul 18, 2017 at 10:36 AM, Michael Tortorella <w2iy@verizon.net>
wrote:

> Hi Mark,
>
> I am grateful that you pitched in and offered help with my Eagle com
> problem.  Not solved yet, but I am awaiting a double-shielded USB cable
> that
> I hope will help.
>
> But to your issue: I had a similar issue with N1MM+ and the forum suggested
> dialing down the baud rate to 38400 and this helped.  Maybe you can try
> this.  Alternatively, maybe try one of the free logging programs (N1MM,
> DXLab, etc.) just to see it the problem persists.  I have had good
> experiences with both N1MM+ and DXLab.
>
> We have become a nation of system administrators :(
>
> 73
> Mike W2IY
>
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Mark
> killen
> Sent: Tuesday, July 18, 2017 12:12 AM
> To: Discussion of Ten-Tec Equipment
> Subject: [TenTec] Ten Tec Eagle com3 problem
>
> I have tried since I bought this radio to use it on the digital modes but I
> have failed.  When I run HRD  I the this Error:  TT eagle, com 3 57600 the
> system cannot find the file specified.  Also, if I don't get this error
> then when I run DM780  I get an open com3 error.  I have updated hrd, I
> have reinstalled the drivers many times (and yes I have turned off driver
> device signing)  I have tried reassigning comports, I have worked with the
> HRD technicians and all to no avail.  I have done everything that I can
> think of and nothing works.  It has to either be a windows problem or a usb
> to uart driver problem and I just don't know how to fix it.  I'm running
> Windows 10 by the way.  And I've tried this on 2 other windows 10 machines
> and I have the same problem.
>
> So, I'm begging...HELP!!!
>
> Mark Killen
>
>
> --
> Mark L. Killen KD8QIG
> 740-550-3778
> facebook.com/taraw8va
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> ---
> This email has been checked for viruses by AVG.
> http://www.avg.com
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>



-- 
Mark L. Killen KD8QIG
740-550-3778
facebook.com/taraw8va
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>