TenTec
[Top] [All Lists]

Re: [TenTec] Orion II Power Connector Replacement

To: Rod Greene <w7zrc@yahoo.com>, denton sprague <denton@oregontrail.net>, Discussion of Ten-Tec Equipment <tentec@contesting.com>, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Orion II Power Connector Replacement
From: Rod Greene via TenTec <tentec@contesting.com>
Reply-to: Rod Greene <w7zrc@yahoo.com>, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Wed, 8 Mar 2017 14:07:50 +0000 (UTC)
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Just a final quick update. Finished installing the PowerPole connector 
yesterday afternoon and made a new cable that now runs directly to the power 
supply. No flicker or problems and I swear the O2 is working much better. Was 
tedious going through all those little screws and getting it all back together. 
Good to have pictures and notes - can't remember how things go, and can't see 
so well up close anymore - ha! Getting older isn't for the faint.

Thanks for all the help and suggestions. 73, Rod/w7zrc


      From: Rod Greene via TenTec <tentec@contesting.com>
 To: Rod Greene <w7zrc@yahoo.com>; denton sprague <denton@oregontrail.net>; 
Discussion of Ten-Tec Equipment <tentec@contesting.com>; Discussion of Ten-Tec 
Equipment <tentec@contesting.com> 
Cc: Rod Greene <w7zrc@yahoo.com>
 Sent: Thursday, March 2, 2017 9:18 AM
 Subject: Re: [TenTec] Orion II Power Connector Replacement
   
I ordered the little plates to mount the power pole connectors on the back of 
the Orion. Any suggestions on the process of installing the power poles that 
way would be appreciated and for bypassing the fuse. 

Thanks again and 73, Rod/w7zrc

      From: Rod Greene via TenTec <tentec@contesting.com>
 To: denton sprague <denton@oregontrail.net>; Discussion of Ten-Tec Equipment 
<tentec@contesting.com> 
Cc: Rod Greene <w7zrc@yahoo.com>
 Sent: Wednesday, March 1, 2017 1:51 PM
 Subject: Re: [TenTec] Orion II Power Connector Replacement
  
I agree, it looks pretty flimsy, so think I will bypass and use a different 
fuse.
Thanks and 73, Rod/w7zrc


      From: denton sprague <denton@oregontrail.net>
 To: Rod Greene <w7zrc@yahoo.com>; Discussion of Ten-Tec Equipment 
<tentec@contesting.com> 
 Sent: Wednesday, March 1, 2017 8:17 AM
 Subject: Re: [TenTec] Orion II Power Connector Replacement
  
take a gander at that little fuse holder while you are in there….kinda puny in 
my observation. 
when I redo my Oroin 1, I will bypass that fuse holder with a big fuse holder 
on a new power cords pigtail.
> On Mar 1, 2017, at 6:25 AM, Rod Greene via TenTec <tentec@contesting.com> 
> wrote:
> 
> 
> 
> 
> I'm pretty sure I've got the bad power connector problem. Rig intermittently 
> gives a loud "POP" and then reboots. What's the best recommended solution? 
> Solder the power cable directly to the board without the molex connector - or 
> - do the power pole replacement? I'm leaning to the direct wire mod.
> Suggestions please! Thanks and 73, Rod/w7zrc
> 
> 
> 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec


  
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec


  
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec


   
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
<Prev in Thread] Current Thread [Next in Thread>