You should try a Corsair II if you want to experience real QSK at higher
speeds!
BTW, it took a LOT of work to get the Orion as good as it ended up. The
beta testers were all over TT to improve it in early firmware versions and
tested/measured the heck out of it.
73, Barry N1EU
On Mon, Nov 7, 2016 at 3:35 AM, Kim Elmore <cw_de_n5op@sbcglobal.net> wrote:
> I've noticed the same thing with my OII but only on 40/80/160 m bands. 2%
> fixed it with mine as well.
>
> Because the radio is essentially SDR, I've noticed that the
> within-character QSK rx is lost around 20-25 WPM, depending on the QSK
> delay setting; between characters is always OK at any speed I can handle.
> On my olde analog TS-930S, the QSK hangs in there pretty much as fast as I
> care to go.
>
> 73,
>
> Kim N5OP
>
>
> On 10/25/2016 6:20 PM, Barry N1EU wrote:
>
>> 2% is nothing, you'll be absolutely fine
>>
>> 73, Barry N1EU
>>
>> On Tue, Oct 25, 2016 at 5:56 PM, Rod Greene <w7zrc@yahoo.com> wrote:
>>
>> Barry,
>>>
>>> Sorry if this appears as a repeat message - but I didn't see my previous
>>> reply come through. Anyway, that fixed it. I can go down as low as 2% but
>>> not any less.
>>>
>>> Thanks much! 73, Rod/w7zrc
>>>
>>>
>>> ------------------------------
>>> *From:* Barry N1EU <barry.n1eu@gmail.com>
>>> *To:* Rod Greene <w7zrc@yahoo.com>; Discussion of Ten-Tec Equipment <
>>> tentec@contesting.com>
>>> *Sent:* Tuesday, October 25, 2016 3:32 PM
>>> *Subject:* Re: [TenTec] Audio Popping - Orion II with V3.033xe
>>>
>>> Try adding 10% CW QSK Delay in the CW Menu.
>>>
>>> 73, Barry N1EU
>>>
>>> On Tue, Oct 25, 2016 at 5:26 PM, Rod Greene via TenTec <
>>> tentec@contesting.com> wrote:
>>>
>>> All,
>>> I just loaded version 3.033xe and have entered all my custom settings. I
>>> know I'm a little late trying this update. Anyway, all seems to be
>>> working
>>> okay except when keying CW. When the key breaks (when I let up on the
>>> key),
>>> I get a pop in the audio monitor. Happens all the time even with the
>>> S-Tone
>>> at zero.
>>>
>>> Is this a known problem and do I just need to go back to version 3.033xd
>>> to correct it, or have I missed a setting somewhere?
>>> Thanks and 73, Rod/w7zrc
>>> ______________________________ _________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/ mailman/listinfo/tentec
>>> <http://lists.contesting.com/mailman/listinfo/tentec>
>>>
>>>
>>>
>>>
>>>
>>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
> --
>
> Kim Elmore, Ph.D. (Adj. Assoc. Prof., OU School of Meteorology, CCM, PP
> SEL/MEL/Glider, N5OP, 2nd Class Radiotelegraph, GROL)
>
> /"In theory there is no difference between theory and practice. But, in
> practice, there is." //– Attributed to many people; it’s so true that it
> doesn’t matter who said it./
>
> _______________________________________________
>
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|