I have replaced an Orion illuminator and half a dozen Icom 756 xxx illuminators
with excellent results using LED’s from LCD Parts.
They sell drivers if your radio’s controller is not compatible with a
particular lamp that you want to use.
Ten Tec uses the LED’s in triads in series, and a few triads in parallel. That
makes the allowable drive voltage about 3.7 volts. This is pulse width
modulated to hold the brightness (and heat) down.
The LCD Parts LED’S are all in series, thus requiring ~13.8 volts drive, also
pulse width modulated.
I did manage to do my last install and preserve some degree of brightness
adjustment using the original brightness control on my last Pro 3 and am
certain this would work on the Orion as well.
However, Ten Tec did not make the illuminator brightness a consumer adjustment
in the Orion (I do not know why) and I cannot even find it in the service
manual. I am assuming they set the PWM duration to the level they thought gave
good illumination, reasonable heat and good lifetime.
I guess 14 years would be defined as good lifetime…
Ten Tec were was ahead of everyone else at the time with their LED illuminators
as all of the competition then used CFL’s, which stink, have always stunk and
always will stink. Short lifetime, ugly color rendition, slow achievement of
equilibrium, toxic material in large quantities, very fragile, require very
high voltage. YUK! I won’t even use them for household illumination any more.
Gary
W0DVN
> On May 8, 2016, at 8:42 PM, <km2km@twc.com> <km2km@twc.com> wrote:
>
> Carl, I did not have any problems with the decimals or any other feature of
> the screen.
>
> Joe, K8MP, TNX for the comment -
>
> I wonder just how many hours these back lights last?
>
> 73 all,
>
> Kris KM2KM
> MERSCHROD
> 123 Warren Road
> Ithaca, NY 14850
>
> ---- Carl Winkles <jcwinks@att.net> wrote:
>
> =============
> Hi Kris. The last time I replaced the backlight in a Delta II the rig wound
> up with an extra dot in the display. Ten Tec said it was caused by stray
> capacitance. I am just curious if you had the same issue?
> CarlK4SEV
>
> On Sunday, May 8, 2016 10:04 AM, "km2km@twc.com" <km2km@twc.com> wrote:
>
>
> Just a quick note, For what it is worth
>
> I had bought this replacement from England a few years ago and only now got
> to it - sorry I do not have the name of the company. The backlight strip
> came with wires and a plug.
>
> The replacement is delicate, but not a struggle:
>
> Remove top and bottom covers.
>
> Loosen the top two screws on the side of the front panel,
>
> Gently tilt the front panel forward;
>
> Unplug three plugs that are on the screen - there are two plugs on the right
> side, and one plug (serving the back light) on the left of the screen. (Make
> note of which is which - but it is really straight forward)
>
> Unscrew the screen - four screws.
>
> lift off the screen by gently pressing from the front - might be a snug fit.
>
> The backlight is plastic and slips between the glass screen and the
> intelboard and is fed by two wires that wrap around the board from the two
> prongs frowm which one of the plugs was pulled.
>
> snip the two wires (really are like thick traces of flat wire) as close to
> the backlight strip as possible.
> Gently fold back the two traces so that they are out of the way of the
> backlight strip as you slide it out.
>
> I used needle-nosed pliers to pull the backlight strip out.
>
> The replacement back light had two wires and a plug long enough the replace
> the wires in the harness and not use the plug and folded back wires on the
> board. I chose to snip them off leaving just enough wire to solder to the
> folded back traces. I used tape to hold the traces and wires to the board.
>
> In retrospect, the alternative, use the plug and all, is probably the better
> idea in retrospect, but the plug needs to be whittled a bit to fit. That
> would save snipping the wires, pealing the insulation and soldering.
>
> It is an easy repair and it is so nice to see the screen without having to
> shine a bright light on it!
>
> 73
>
>
>
> Kris KM2KM
> MERSCHROD
> 123 Warren Road
> Ithaca, NY 14850
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|