yet another follow up…
lately been noticing that the sub receiver is deaf until the rig warms up…then
have to go to 20 meters via sub receiver, switch between sub rx buttons, listen
for hash on the VFO A sub receiver setting, go back to VFO B sub rx button then
reboot the rig…..
then the sub receiver will operate normally.
still feels like connector corrosion problems.
will probably open up the rig, clean and re-seat the cables and connectors in a
couple of months if don’t sell the rig.
Have an Orion II coming in a couple of days, so my time will be tied up with
it.
> On Oct 21, 2015, at 11:01 AM, denton sprague <denton@oregontrail.net> wrote:
>
> well…shoot..
> that lasted all of 1/2 hour!
> The past week or so, I has been inoperative on boot up…
> and it boots up with swishing noise that repeats itself or it seems to work
> but can’t her anything but background (processor) noise, or receive sigs are
> way down in the background.
> So for the time being it will be designated back up rig in the closet…and
> will run my omni 7 for the duration.
> I also have a chance ti purchase an unknown condition orion sub receiver
> board but not too sure want to mess with that.
> I seems to be something that is not letting the sub receiver board connect to
> the rest of the system correctly..
> I have not yet done much in the way of diagnostics…but will take some time
> this fall to pull the sub receive board and see if anything amiss…cold solder
> joints, etc, clean contacts and trace down cabling.
>
> On Oct 12, 2015, at 9:07 AM, denton sprague <denton@oregontrail.net> wrote:
>
>> a little followup..
>> sub rx was inoperable this am…booted up with sub rx on ant 1 and vfo b
>> enabled yesterday.
>>
>> after letting the rig on for about 3 hours, I rebooted the rig with sub rx
>> off on the ant and vfo buttons.
>>
>> after reboot, enabled sub rx on vfo b and ant 1 buttons. Sub rx now works
>> normally….
>>
>> On Oct 11, 2015, at 11:27 AM, denton sprague <denton@oregontrail.net> wrote:
>>
>>> thanks…apparently that was it om!!
>>> On Oct 11, 2015, at 11:13 AM, Tim Wininger <ky5rtim@gmail.com> wrote:
>>>
>>>> Need both SUB RX VFO and Ant1 SUB RX depressed.
>>>>
>>>> That's how I use this sub rcvr hr. Hope it's just that.
>>>>
>>>> GD Tim, AB4B
>>>>
>>>> On Sun, Oct 11, 2015 at 12:01 PM, denton sprague <denton@oregontrail.net>
>>>> wrote:
>>>>
>>>>>
>>>>> Hi all…my trusty Orion that came back from TT for processor board
>>>>> replacement a few months ago seems to have no receive signals…this
>>>>> happened this am when booting up the rig.
>>>>> I use ant 1 as main rx/tx as well as sub rx.
>>>>> I can hear the sub noise come up when pressing the sub rx button, but
>>>>> evidently getting no signals from the antenna.
>>>>> I have only one hf antenna.
>>>>> Did a master reset to no avail.
>>>>> loose cable maybe??
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec@contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|