I found the technical service fella who answered the phone to be evasive when I
stated, "Look...there is a long lead time (actually unknown) for these speakers
to arrive....do you know of a source for a replacement?" His response was a
shot "No."
I just can't believe they don't know of a replacement soured - maybe, I'm all
wet and expecting too much..
> From: wfpjr@hotmail.com
> To: tentec@contesting.com
> Date: Tue, 13 Jan 2015 15:04:23 -0800
> Subject: Re: [TenTec] Jupiter speaker replacement....
>
> I was thinking of buying a new Omni VII but your experience causes me concern
> that something is happening at Tentec and I am wondering about owning any
> TenTed equipment. Any comments??
>
> > From: rodenkirch_llc@msn.com
> > To: tentec@contesting.com
> > Date: Tue, 13 Jan 2015 15:18:25 -0700
> > Subject: [TenTec] Jupiter speaker replacement....
> >
> >
> >
> >
> >
> > Ooooops, sorry about that (thanks to Al, WB5JNC, for asking about a
> > picture/drawing)....go to this URL:
> >
> > http://www.loudspeaker.com.cn/English/ProductView.asp?Id=803
> >
> > > From: wb5jnc@centurytel.net
> > > To: rodenkirch_llc@msn.com
> > > Subject: Re: [TenTec] Jupiter speaker replacement....
> > > Date: Tue, 13 Jan 2015 16:12:02 -0600
> > >
> > > Do you have a pic or other info on the speaker (power rating, etc.)? If
> > > you
> > > don't mind used I'll take a look to see if I can match it either in my or
> > > my
> > > SK dad's accumulation.
> > >
> > > Otherwise, I think the online outfits like Jameco etc. might have
> > > something.
> > >
> > > 73, Al
> > >
> > > On Tue January 13 2015 3:54:04 pm you wrote:
> > > > ....I'm asking one more time if anyone knows of a replacement speaker
> > > > for
> > > > the Jupiter. I called the service department at Ten Tec and they have
> > > > it on
> > > > back order with no known delivery date. I asked if they knew of or could
> > > > recommend a replacement but, as expected, the fella I talked to knew
> > > > nothing. I sent the service department an e-mail asking if I could get
> > > > in
> > > > the queue for obtaining one of the back ordered speakers but no reply
> > > > so....figure I'm on my own for the near future as I need to replace the
> > > > speaker before I sell it so I can purchase a new Argonaut VI...or
> > > > something
> > > > like that.
> > > >
> > > > Dimensions are 60 mm (2.375 inches) between mounting holes and a
> > > > diameter
> > > > between opposite corner holes of 84 mm (3.313 inches).
> > > >
> > > > I believe the speaker can be 4 or 8 ohms.
> > > >
> > > > Thank you, in advance, for ideas or suggestions.
> > > >
> > > > 72/73, Jim Rodenkirch K9JWV
> > > >
> > > > _______________________________________________
> > > > TenTec mailing list
> > > > TenTec@contesting.com
> > > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
> >
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|