I don't think it's the signal levels unless there is a bad connection insid
ethe Easy-DIGI or her
connected it to the wrong pin on the ACC1 cable.
There is plenty of audio coming out of the laptop.
On 12 Aug 2014 at 14:48, Louis Ciotti wrote:
> Which one did you get? The kit, the assembled PCB, the assembled one in a
> box with cables, or the assembled in a box with box?
>
> Looks like he used some impedance transformers... (To provide isolation would
> be my bet) in the audio path with a fixed resister to set the level. I
> suspect the signal levels are wrong on the acc1 jack.
>
> -----Original Message-----
> From: "Brian Carling" <bcarling@cfl.rr.com>
> Sent: 8/12/2014 2:25 PM
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Subject: Re: [TenTec] Omni VII Digital
>
> It's a commercial interface I got from eBay called EASYDIGI that appears to
> not be conveying the transmit audio through to the ACC1 connector.
>
> More results soon.
>
> Best regards - Bry Carling
>
>
>
> > On Aug 12, 2014, at 9:53 AM, Louis Ciotti <lciotti1@gmail.com> wrote:
> >
> > It should not be difficult. If using the TenTec provided cable (From
> > the Manual):
> >
> > WHITE = pin 1, line level audio input.
> > YELLOW = pin 4, line level audio output.
> > RED = pin 5, FSK.
> > BLACK = pin 3, push to talk
> > Ground from the 46176 cable is connected to pin 2.
> >
> > Have you verified the cable is correct? It also sounds like you may
> > be connecting Pin 1 to the speaker output. Not knowing what is inside
> > the Omni VII, I wonder if you provided it with too much voltage on
> > that pin at damaged the input circuit there.
> >
> >> On Tue, Aug 12, 2014 at 8:06 AM, <bcarling@cfl.rr.com> wrote:
> >> Thank you Ed,
> >>
> >> I have tried all of those things. Still no audio on transmit wit hthe OMNI
> >> VII.
> >> I am glad my FT857D wasn't this difficult.
> >>
> >> 73 de AF4K, Bry
> >>
> >>> On 11 Aug 2014 at 12:26, Edward Feustel wrote:
> >>>
> >>> Brian,
> >>> I had the same problem on my Orion (565) while using FLDIGI with the
> >>> Ten-Tec kit to use the buffered audio input/output to/from the computer
> >>> soundcard:no transmit.
> >>>
> >>> It was resolved when I did three things:
> >>> 1. Shifted the audio input from the mike to the Accessory Input via menu
> >>> 2. Turned on Vox Mode via front panel button
> >>> 3. Adjusted the gain on the auxiliary input via the menu enough to
> >>> invoke the vox via the menu.
> >>>
> >>> Now it works like a champ.
> >>>
> >>> 73,
> >>> Ed, N5EI
> >>> _______________________________________________
> >>> TenTec mailing list
> >>> TenTec@contesting.com
> >>> http://lists.contesting.com/mailman/listinfo/tentec
> >>
> >>
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|