TenTec
[Top] [All Lists]

Re: [TenTec] Scout has vy low Pwr out on some bands

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Scout has vy low Pwr out on some bands
From: GARY HUBER <glhuber@msn.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Thu, 17 Jul 2014 11:42:46 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
How about a coffee filter paper dampened with common lighter fluid.... such as is used to clean CPU and CPU coolers prior to adding the thermal paste?


73 & DX,
Gary - AB9M
-----Original Message----- From: Rick - DJ0IP / NJ0IP
Sent: Thursday, July 17, 2014 9:20 AM
To: 'Discussion of Ten-Tec Equipment'
Subject: Re: [TenTec] Scout has vy low Pwr out on some bands

There are two more bands that still don't work and all modules were
unplugged for about 10 years, laying, gathering dust.  They definitely all
need cleaning.
This has nothing to do with being abscessed, and everything to do with
avoiding near future problems.

I will do it with the two chemicals that I have because I have good
experience with them.
I will first try the toothpick.

As for writing my will on sandpaper; good idea.
At least my daughter would have one thing useful in her inheritance!  ;-)

73 - Rick, DJ0IP
(Nr. Frankfurt am Main)


-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of K8JHR
Sent: Thursday, July 17, 2014 3:48 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Scout has vy low Pwr out on some bands

Eek... I would be careful with metal cleaners.  As I recall, Tarn-X and the
like often leave a film, and residue, etc., that is hard to get out of
cracks, crevices, and other small areas, despite it claiming to be
apply-and-rinse easy to use..    It is made with Thiourea and Salfamic
Acid, a rather caustic aqueous acid product.  While it might remove some
oxidation, it could also damage the other materials inside the device, such
as plastics, insulating phenolic wafers and similar materials.

The Tar-x Product Data Sheet says:

Restrictions on Use:
Incompatible with strong oxidizing agents, acids,
bases, and bleach. Do not use on stainless steel,
chrome, pewter, aluminum, brass, zinc, marble,
pearls, opals, and other porous stones.



Rick -- You are obsessing over this.  Why not stop now, when you can,
and it still works.   I really believe in the adage:  "If you fix
something long enough, eventually you will break it."   Anyone who has
stripped a screw over-tightening it knows this is true.  If the Scout
cartridge works full power out, why not just stop there and call it good.
Clean what you can easily reach, and stop, or you may reap the
balance of the adage, and eventually break it.   If it is working...
close it up and call CQ on it.


As for the bond paper... even though you have a 'lot of GRIT", I doubt
you would write your Will on sand paper...    ;-)

Just MY take.

====================  K8JHR ======================





On 7/17/2014 4:14 AM, Rick - DJ0IP / NJ0IP wrote:
Hmmm, well I don't know what bond paper is.  Perhaps what I call
Emery paper.
But it is very difficult to get anything down in there.

______________________________________________
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>