TenTec
[Top] [All Lists]

Re: [TenTec] Paragon power problem

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Paragon power problem
From: "Robert Mcgraw" <rmcgraw@blomand.net>
Reply-to: rmcgraw@blomand.net, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Mon, 23 Sep 2013 06:55:14 -0500 (CDT)
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Many times I've found radios of this age/vintage just need a good
connector cleaning.  Very often just unplugging the connector, applying a
very small amount of contact cleaner and then reinserting the plug is all
that's needed to make it perform just like new.

73
Bob, K4TAX






> The gounding looked goo and all mounting screws has lock washers that bit
> into the board edge traces very well. Actually, after more fiddling
> around I
> may have located the problem. The coax connector from this LL Amp board
> to
> the final amp module may have just gotten a bit dirty such that flexing
> the
> board in the center of the opposite side was causing it to make a poor
> connection. I cleaned the pins on that connector and the power has
> remained
> steady since. I'll be watching it, but for now all seems OK.
>
> =Vic=
>
> ----------------------------------------------------------------------------
> --------------------------------
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Subject: Re: [TenTec] Paragon power problem
> From: GARY HUBER <glhuber@msn.com>
> Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
> Date: Sun, 22 Sep 2013 10:53:02 -0500
> List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
>
> Vic,
>
>
> As a former owner of a 585 and having sent mine back several times over
> the
> ten years I had it, I learned that some of the board problems had to do
> with
> grounding. In fact one mod was re-solder the corners of the board, put
> star
> washers on both sides and then with a slightly longer screw remount
> securely. Is there any chance you have an intermittent grounding problem
> rather than a bad board?
> 73 ES DX,
> Gary -- AB9M
>
>
> -----Original Message----- From: Vic Klein
> Sent: Sunday, September 22, 2013 10:11 AM
> To: tentec@contesting.com
> Subject: [TenTec] Paragon power problem
>
> My 585 paragon has developed an intermittent issue with power dropping
> off
> to QRP levels and the ALC light going off. No other issues exist and the
> signal remains clean and distortion-free when this occurs. Some
> experimenting indicates the problem is with the Low Level Amp/NB board
> which
> is located above the Loop boards enclosure. Flexing the board in the area
> of
> the Q connector replicates the issue and either drops or restores power.
> I
> have cleaned the contacts and even swapped connectors, and reflowed
> solder
> in all the joints in that quarter of the board between that connector and
> Q4, but the problem remains. This board is marked 81560 on the board, and
> is
> slightly different than the 81350 as shown in the manual. Does anyone
> happen
> to have a spare lying around that they would like to part with?
>
> =Vic=
> WA4THR
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>


-- 
Disclosure:
I am a Tentec Ambassador and compensated according to the Tentec
Ambassador plan. I serve as a volunteer beta test person for the Omni
VII, Eagle and Argonaut VI products.   Otherwise, I hold no business or
employment interest with Tentec.

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>