How about a plain old FOOT SWITCH, on the amp relay line? Mash the foot
switch and then just send with the rig and it gets amplified. Forget to use
the foot switch and NO HARM DONE, other than the guy at the other end
wonders where you went :-)
K8cv
-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Bob McGraw
- K4TAX
Sent: Thursday, August 08, 2013 8:12 AM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Argo V amp keying
Just remember, making changes of this magnitude might put one in the
position of a "very underpaid design Engineer". In other words, "if one
THINKS they know what they are doing, best STOP and ask someone that has
done it before successfully".
I agree with Rick, adding something like this might be fatal to the radio.
Now lets look at the issue a bit differently. Why not use your keyer with a
suitable driver to key the amp and to key the radio. It works this way for
situations where one does not have QSK keying ability when using the
Centurion amp and some other radio that does not have QSK capability. The
key is connected to the amp {not the radio} and the keying circuit in the
amp then keys the radio upon key closure. The AUX connector on the back of
the ARGO V does have access to the PTT for that reason.
73
Bob, K4TAX
----- Original Message -----
From: "Rick - DJ0IP / NJ0IP" <Rick@DJ0IP.de>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Thursday, August 08, 2013 12:35 AM
Subject: Re: [TenTec] Argo V amp keying
> Guys, BE VERY CAREFUL about bringing the T-line out of the rig.
>
> SPECIFICALLY, DO NOT DO THAT!
>
> This is a signal which runs through many stages of the radio.
> If anything unusual externally touches that line, lots of damage can
> occur.
>
> You MUST buffer the line with a transistor before bringing it out.
> Then the worst thing you will do is blow that transistor.
>
> Examples of what might happen:
>
> <> It gets inadvertently connected to an older amp which uses 120v for
> keying its relay. "GAME OVER"
> <> It gets inadvertently connected to a newer amp which uses 12v for
> keying
> its relay. "Smoked Silicon"
> <> It shorts to ground. "If you're lucky, it just blows a fuse. Murphy?"
>
> *** Buffer the signal before you bring it out of the rig! ***
>
> 73
> Rick, DJ0IP
>
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Mark
> N8COO
> Sent: Thursday, August 08, 2013 12:48 AM
> To: tentec@contesting.com
> Subject: Re: [TenTec] Argo V amp keying
>
>>
>> Message: 12
>> Date: Tue, 06 Aug 2013 08:06:53 -0400
>> From: Dave Edwards <kd2e@comcast.net>
>> To: tentec@contesting.com
>> Subject: Re: [TenTec] Argo V amp keying
>> Message-ID: <5200E6DD.20002@comcast.net>
>> Content-Type: text/plain; charset=ISO-8859-1; format=flowed
>>
>> Is that not the line already available on the accessory connector?
>> (for keying the radio)
>>
>> ...Dave
>>
>
> Hi Dave,
>
> Sorry I did not specifically answer your original question. Please allow
> me
> to try again:
>
> The PTT you mentioned earlier (on AUX 1) is to be able to place the rig
> into
> transmit mode, when grounded - like for a transmit foot switch, or a
> typical soundcard interface that utilizes hard keying of the rig such as
> through the computer's serial port. The manual calls it "keyline input"
> (page 6.) It does not provide closure upon transmit.
>
> As shipped from the factory, the line ("T" line) is not available on the
> AUX
> 1 connector, or any of the other connectors, nor is there a factory
> installed provision for keying of an external amp through relay closure or
> other means on the Argonaut V.
>
> The replies given for addition to your rig of a keying circuit for your
> amp
> will do the job, but will involve some modification of the rig. You might
> want to bring the "T" line out though the slot for the fan wires or
> somewhere similar and mount the keying circuit externally, thus making it
> easily reversible and no drilling any holes - if that is a concern.
>
> 73, Mark N8COO
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|