TenTec
[Top] [All Lists]

Re: [TenTec] O II PSK setup? Resending...no responses

To: tentec@contesting.com
Subject: Re: [TenTec] O II PSK setup? Resending...no responses
From: Rsoifer@aol.com
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Fri, 14 Jun 2013 15:42:01 -0400 (EDT)
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
The only thing I would add is that if you set TX audio to Both, be  sure 
the mic is switched off.  Otherwise, set TX audio to  AUX.
 
73 Ray W2RS
 
 
In a message dated 6/14/2013 4:54:55 P.M. GMT Standard Time,  
g3rxp@btinternet.com writes:

Tom,

I have the O2 and a microham keyer 2 so the settings  should be comparable.

I run SSB CW and Data and I dont change the  settings when switching from 
one 
mode to another. I run N1MM (Contest  logger ) for digital and CW/SSB.

On Data I run MVARI for PSK but I use  MMTTY for FSK transmission which the 
O2 works extremely well.

SSB  settings on Menu
Aux input gain at 100 - so I can turn the gain down with  the Microham.
TX Audio --- Both.
H/W Mic gain ---- 14db

Mike gain  at the top (next to Tune button) to 35.

Menu - Other
Line output  main
Line Output level -High.

Mode on the rig USB

MVARI  Settings. at the top of the digital window.
DI1
Input sound card  ---------   0 Microham codec  (S)
Output sound  card-------    1 Microham codec (S)

DI2
Input Sound  card   ----Auto Detect
Output sound card ----Auto  Detect


Once you have done all that you then have to make sure the  Microham Router 
ports are all setup correctly.   This is a topic  on its own and you need 
to 
look at the Microham manual for help. I presume  it has its own sound card 
other wise the cards in the settings of MMVARI  will be those in your 
computer.

I have no experience of Logger 32  or JT65HF

Good Luck

73 Dave  G3RXP








----- Original Message -----  
From: <cx7tt@4email.net>
To:  <tentec@contesting.com>
Sent: Friday, June 14, 2013 1:15  AM
Subject: [TenTec] O II PSK setup? Resending...no  responses


>
>
>
> Hola,
>
>  Setting up O II for first time for PSK ops. Looking at the manual,  p42,
> Fig 4-6. I set under the SSB menu, Input Device to AUX and AUX  gain to
> 75; then Audio Menu, TX EQ to -14db and finally Top Row menu,  "Mic" to
> zero.
>
> Have I left anything out? I assume that  correct mode is USB?
>
> The O II goes to Microham mK II then  Logger 32 for MMVARI.  Are there
> any settings different from  MMTTY? Can the same settings for PSK be used
> for the JT65HF  software?
>
> 73
> Tom
>  CX7TT
>
>
>
>
>  _______________________________________________
> TenTec mailing  list
> TenTec@contesting.com
>  http://lists.contesting.com/mailman/listinfo/tentec  

_______________________________________________
TenTec mailing  list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>
  • Re: [TenTec] O II PSK setup? Resending...no responses, Rsoifer <=