TenTec
[Top] [All Lists]

Re: [TenTec] OrionII and MixW Config settings

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] OrionII and MixW Config settings
From: "Bob McGraw - K4TAX" <RMcGraw@Blomand.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Fri, 16 Nov 2012 20:12:23 -0600
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
OK, so the convention for AFSK is LSB. My goof! Guess I've been operating too much PSK-31 which does typically use the USB mode regardless of band convention. Actually, either sideband will decode correctly in PSK-31.

Thanks for the clarification.  LSB for AFSK.

73
Bob, K4TAX


----- Original Message ----- From: "Stan Brock" <sales@tentec.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Friday, November 16, 2012 12:35 PM
Subject: Re: [TenTec] OrionII and MixW Config settings


Bob,

I think for AFSK you want to be in LSB instead of USB.

Stan

On Thu, Nov 15, 2012 at 3:48 PM, Bob McGraw - K4TAX <RMcGraw@blomand.net>wrote:

Tony:

You mention FSK,  the MixW program provides AFSK and not a FSK signal
although it says RTTY.  For AFSK the Orion should be in USB mode.  Check
the value of the Line/Aux Gain as it may be 0 or too low.  Raise the
Line/Aux gain to a mid way value to start.   Also the Windows Mixer will
adjust the audio level going to the radio.

From MixW drop down menu select Configure and then  Output volume.  This
brings up the Windows Mixer.  The two sliders marked Volume Control and
Wave are the controls for the audio out of the computer.   I normally run
mine about mid range and then adjust the Wave slider for some 30 to 40
watts of data power output. The Orion should be set to 100 watts power and
the Speech Processor should be off.

73
Bob, K4TAX




----- Original Message ----- From: "EI6DL" <ei6dl@eircom.net>

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Wednesday, November 14, 2012 3:13 PM

Subject: [TenTec] OrionII and MixW Config settings


Hello ! I have just connected the TenTec Model 712 USB to the Aux/I on my
Orion II and ran MixW on my PC .The programme is reading the Digi fsk
signals ok but i can not get the programme configed to transmit /send a sig
I have the programme set for the TenTec Orion II and have gone into the
menu on the Orion II and changed the TX Audio source to Aux instead
Mic.Still will not force the transciever to TX a digi sig ?? Can anyone
help ? 73'es Tony EI6DL
______________________________**_________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/**mailman/listinfo/tentec<http://lists.contesting.com/mailman/listinfo/tentec>



______________________________**_________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/**mailman/listinfo/tentec<http://lists.contesting.com/mailman/listinfo/tentec>




--
Stan Brock, WD0BGS
Amateur Radio Sales
Ten-Tec, Inc.
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec



_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>