I assume that the default settings are defined in the firmware, but in my case
they do not correspond to the actual meter readings for each step. In my case,
they are much stingier. When I set each one to correspond to the meter, then it
way too generous. Also, the maximum count of 255 only drives the meter to S9+30
or so. Same on TX, full power output deflects the meter to only about 70, or
about the same place as the max receive level. Methinks there is something
afoul in the meter circuitry.
Is there perhaps a hardware adjustment for calibrating the meter movement
somewhere?
Any suggestions?
N4UC
> Date: Sat, 31 Dec 2011 22:13:32 +0000
> From: barry.n1eu@gmail.com
> To: tentec@contesting.com
> Subject: Re: [TenTec] Orion s-meter calibration
>
> Tom, it came up a while back on the reflector. My memory ain't what
> it used to be, although it probably never was what it used to be ;-)
>
> 73 & Happy New Year to all,
> Barry N1EU
>
> On Sat, Dec 31, 2011 at 9:54 PM, Tom Berry <tberry1@triad.rr.com> wrote:
> > Thanks Barry. OK on not recommending that anybody change them.
> > I'm curious as to how AL7CR knew that feature was there..
> >
> > 73 Tom AA4VV
> >
> >
> > On 12/31/2011 4:48 PM, Barry N1EU wrote:
> >> I've never seen a description of what those values mean. I just
> >> played with them until the Orion s-meter responded similarly to a
> >> known good receiver's s-meter. I can't really recommend that anybody
> >> else changes those values.
> >>
> >> Barry N1EU
> >>
> >> On Sat, Dec 31, 2011 at 9:17 PM, Tom Berry<tberry1@triad.rr.com> wrote:
> >>> Let me see if I understand this function. I would select an S meter
> >>> value (say S9) then change the digital count so that the S meter reads
> >>> S9. Is that correct?
> >>>
> >>> 73 Tom AA4VV
> >>>
> >>>
> >>>
> >>> On 12/31/2011 3:48 PM, Barry N1EU wrote:
> >>>> Thanks - it's uncharted territory in there but I think I managed to
> >>>> improve things. I was careful to record the original values before
> >>>> mucking around.
> >>>>
> >>>> 73, Barry N1EU
> >>>>
> >>>> On Sat, Dec 31, 2011 at 7:18 PM, AL7CR<al7cr@punakea.com> wrote:
> >>>>> Go to the RX menu and press the 15m band select key. This will bring up
> >>>>> a screen that allows you set the S meter in digital counts.
> >>>>>
> >>>>> AL7CR
> >>>>>
> >>>> _______________________________________________
> >>>> TenTec mailing list
> >>>> TenTec@contesting.com
> >>>> http://lists.contesting.com/mailman/listinfo/tentec
> >>> _______________________________________________
> >>> TenTec mailing list
> >>> TenTec@contesting.com
> >>> http://lists.contesting.com/mailman/listinfo/tentec
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|