TenTec
[Top] [All Lists]

Re: [TenTec] Eagle Firmware Version V1.810 Posted, RX320D GUI Posted. Pe

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Eagle Firmware Version V1.810 Posted, RX320D GUI Posted. Pegasus GUI to follow
From: Dave Edwards <kd2e@comcast.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 24 May 2011 08:32:09 -0400
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Just curious....Did the Argo V have any updates?
I ask because from the day I purchased it, until now...many years later, I 
never performed any updates on it.

....Dave

Sent from my iPad

On May 24, 2011, at 8:22 AM, "Henry, John" <jhenry@tentec.com> wrote:

> Hi John,
> 
> My desire is to provide an update a year for each of the main rigs we
> still sell. Namely Orion(s), OMNI-VII, Eagle, and Jupiter.
> To help some Jupiter users who are running Windows 7 64 bit, I will be
> posting the Pegasus GUI. Which works with the Pegasus and the Jupiter.
> This isn't a firmware change, but it does help many Jupiter and
> Pegasus users.
> Note, we may not make a new update every year for all rigs, some may
> have more than one, etc., all depends upon what is in the works and
> the new products status and time available, etc.
> 
> When we get to the end of an update cycle for an existing rig, I do
> look at the open issues (if any) of each of the rigs, the planned and
> desired feature enhancements, re prioritize them, and start working on
> that one (or two when possible). We just finished upgrades for the
> aforementioned products, and we are at the end of an upgrade cycle for
> a couple of other existing products, and will then "re prioritize" the
> rigs issues and feature desires again. So I don't have an immediate
> answer to your question, just yet.
> 
> Remember though, we are not sitting still, we do have new rigs in
> definition phase, and we do have new rigs in various development
> phases.  This is not "top secret" information, because every business
> should always be defining the next generational leap rig, and working
> on the next generation improvement rigs, otherwise, they are left
> behind, gone and forgotten. TenTec has been here over 40 years now,
> and I hope to keep myself employed at TenTec for, well, maybe another
> 40....
> 
> Thanks for your query, I know I was asked the same question about the
> Jupiter, Pegasus, OMNI-VII, etc., even the RX320D while at Dayton.
> 
> John
> 
> 
> ----------------------------------------------------------
> John,
> 
> Does this indicate a look at the Jupiter in the near future?
> 
> John Graves
> WA1JG
> jh.graves at verizon.net
> 
> On 5/23/2011 3:30 PM, Henry, John wrote:
>> Eagle Changes include:
>> 
>> V
>> Best Regards,
>> John Henry
>> TenTec Engineering
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>