TenTec
[Top] [All Lists]

Re: [TenTec] Orion 565 Problem with 2.063Xg??

To: Ten-Tec Reflector <tentec@contesting.com>
Subject: Re: [TenTec] Orion 565 Problem with 2.063Xg??
From: Rick W <ve7tk@yahoo.ca>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Fri, 15 May 2009 08:08:11 -0700 (PDT)
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Yes Carl.  Rebooting the Orion (after closing the rig control and logging 
software) rejuvenates the rig and it's back to normal.

73,
Rick
VE7TK


To: 

"Discussion of Ten-Tec Equipment" <tentec@contesting.com>




Subject: 

Re: [TenTec] Orion 565 Problem with 2.063Xg??




From: 

"N4PY2" <n4py2@earthlink.net>




Reply-to: 

N4PY2 <n4py2@earthlink.net>,    Discussion of Ten-Tec Equipment 
<tentec@contesting.com>




Date: 

Fri, 15 May 2009 06:36:14 -0400




: 












What happens if you just turn the radio off and then back on?  Does that get 
it working again?

Carl Moreschi N4PY
121 Little Bell Dr
Bell Mountain.
Hays, NC 28635
----- Original Message ----- 
From: "Bob Close" <rclose@nhwisp.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Friday, May 15, 2009 5:23 AM
Subject: Re: [TenTec] Orion 565 Problem with 2.063Xg??


seems the radio works, but not with someone else's software, so that means
it's a problem with
Ten-Tec's software????
Call  N4PY seems more appropriate

--------------------------------------------------
From: "Rick W" <ve7tk@yahoo.ca>
Sent: Friday, May 15, 2009 1:27 AM
To: "Ten-Tec Reflector" <tentec@contesting.com>
Subject: [TenTec] Orion 565 Problem with 2.063Xg??

> I think I've found a problem with 2.063Xg.  Here's the scenario.
>
>     1) I have my 565 under the control of the N4PY software.
>     2) I go to the RX menu and toggle the AGC System Type (it doesn't seem
> to matter which way I go).
>     3) Back out of the menus
>
> After doing this exercise I lose all serial control of the Orion.  In
> addition the remote pod doesn't work.  The work-around is to turn off the
> software and reboot the Orion.
>
> IF I am not using the serial port with an external program and toggle the
> AGC the remote pod works BUT when I try to start some external software
> the serial port is dead.  The same work-around solves the problem.
>
> Before I report this to T-T I'd be curious if others are experiencing
> this?
>
> Thanks.
>
>
> 73,
>
> Rick
>
> VE7TK
>
>
>
> Website:  http://www3.telus.net/ve7tk
>
>
>      ____________________



      __________________________________________________________________
Yahoo! Canada Toolbar: Search from anywhere on the web, and bookmark your 
favourite sites. Download it now
http://ca.toolbar.yahoo.com.
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>