People will tell you that AFSK can be set up badly, so as to splatter and
make a mess. That's true.
But then again - so can FSK.
I'd do AFSK cause its so much easier....but take the time to learn how to do
it right and make sure to do so.
73 de Gary AA2IZ
----- Original Message -----
From: "Bob McGraw - K4TAX" <RMcGraw@Blomand.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, January 26, 2009 10:26 PM
Subject: Re: [TenTec] Omni VI Mod 3 and RTTY
In my opinion {there's a dangerous word} FSK is for the die hard purist.
AFSK is much easier, specially with today's radios, computers, software and
interface boxes.
73
Bob, K4TAX
----- Original Message -----
From: "Tim Randa" <tranda@cox.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, January 26, 2009 9:20 PM
Subject: Re: [TenTec] Omni VI Mod 3 and RTTY
A quick question on the subject. Why bother with the FSK when AFSK gets
the job done with much less hassle. Is there an advantage to FSK that I
as a extremely casual RTTY user haven't a clue about?
de Tim KØFL
Bob McGraw - K4TAX wrote:
> I too used my Omni VI Plus on FSK. The 250 Hz filter worked will with the
> PBT properly adjusted. The manual covers the alignment of the PBT
> circuit.
>
> One extremely important point in using FSK is that the BFO oscillators
> need
> to be very precisely aligned. Follow the steps in the manual in their
> exact
> order. You probably will find it necessary to do this 2 or 3 times as
> there
> is some interaction with the adjustments. Also, a frequency counter that
> can read something in the order of 9 MHz to a resolution of 0.1 Hz is of
> great help and almost a necessity. For better results, be sure the radio
> is
> operating at room temperature for at least 1/2 hr with the covers in place
> before making these adjustments.
>
> After doing all of this, I too found AFSK was much easier to use. Took
> the
> audio IN and OUT from the connectors on the back panel and I let the VOX
> handle the RX/TX switching.
>
> 73
> Bob, K4TAX
>
>
> ----- Original Message -----
> From: "Ed" <w3nr@comcast.net>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Monday, January 26, 2009 3:15 PM
> Subject: Re: [TenTec] Omni VI Mod 3 and RTTY
>
>
>
>> Jerry Pyle wrote:
>>
>>> I am in the process of setting up my station to run RTTY, preferably
>>> FSK.
>>>
>>> My Omni VI Mod3 has all of the filter slots filled and upon inspection I
>>> found that there is not a 217 filter amongst the bunch.
>>>
>>> I have been on the searchable archives looking for a possible Inrad
>>> filter
>>> that will work in place of the 217 (which we all know TenTec no longer
>>> makes) or another workable solution using my existing 500hz filters.
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>> Jerry - WB7S
>>>
>>> Basin, WY
>>>
>>>
>>>
>>> http://wb7s.home.bresnan.net
>>>
>>>
>>>
>>> 73
>>>
>> I use my Omni6 on RTTY without a problem. Had a 217 and sold it, too
>> narrow. Use LSB and your 500hz filter(s) and you won't have a problem.
>>
>> FSK is fine as long as the 2 xtals are 170Hz apart, any more/less you
>> will not be happy. I use AFSK and as long as it is set right you won't
>> have any problems.
>>
>> If you do use FSK, the PBT needs to be set at 3 o'clock.
>>
>> All that is needed for the FSK keying cicuit is a 1K resistor in series
>> with the TXD line.
>>
>> Ed W3NR
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> ------------------------------------------------------------------------
>
>
> No virus found in this incoming message.
> Checked by AVG - http://www.avg.com
> Version: 8.0.176 / Virus Database: 270.10.13/1916 - Release Date:
> 1/26/2009 7:08 AM
>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|