Oh , might as well try an "Orion salute" = Master reset - or the whole
shebang - maybe its little brain got scrambled.
Hank K7HP
battery ----- Original Message -----
From: "Duane Calvin" <ac5aa1@gmail.com>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Friday, December 05, 2008 7:18 PM
Subject: Re: [TenTec] ORION II and FSK
>I run FSK through my DigiKeyer a lot, and have not seen this offset. Not
> sure what to suggest.
>
> 73, Duane
>
> Duane Calvin, AC5AA
> Austin, Texas
> www.ac5aa.com
>
> -----Original Message-----
> From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
> On Behalf Of David W LeJeune, Sr
> Sent: Friday, December 05, 2008 7:06 PM
> To: 'Discussion of Ten-Tec Equipment'
> Subject: [TenTec] ORION II and FSK
>
> This morning I decided to work RTTY and set up the Orion to Mode FSK as
> normal and fired it up. I use MMTTY and key the FSK line via the EXTFSK
> 1.05 MMTTY plugin and a Rigblaster Pro interface. Worked fine, but no one
> was answering. Thought that was strange, so I fired up an aux receiver to
> make sure everything was keying fine. I Normally use a bandwidth setting
> of
> about 750 hz. When I first got the Orion II, in the FSK mode, the
> bandwidth
> was centered on 2125/2295 as displayed in the MMTTY waterfall display.
> Keying sounded OK on the aux receiver.
>
>
>
> Since I wasn't getting any answers, I changed the bandwidth to 1200 hz and
> fired off a CQ - and sure enough someone answered, but they were 170 hz
> off
> frequency. I use the RIT to bring them on freq and had a nice QSO. Found
> that was normal - everyone else I contacted was 170 hz off, and lo and
> behold, the bandwidth was also off 170 hz - I corrected it in the display
> with the PBT and 170 brought it right back into center with the bandwidth
> narrowed again to 750.
>
>
>
> The manual says that in the FSK mode, the FSK signal is centered in the
> filter bandwidth. Certainly not the case today, but I know it was
> previously. What could have changed. I was able to set things up
> properly
> with RIT at +170 and PBT at +170, and I saved it as USER 1 profile. So
> easy
> enough to reset it.
>
>
>
> Anyone else had this experience? When I first got the Orion II about 2
> years ago, both the RIT and the PBT were at 0, and the waterfall display
> was
> perfectly aligned for 2125/2295 tones when I worked RTTY. Note that this
> was with FSK keying with the MODE switch set to FSK, not AFSK with mode
> switch set to USB.
>
>
>
> Just curious.
>
>
>
> Dave WN5V
>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|