Any chance you can post that photo?
Ron N6IE
www.N6IE.com
----- Original Message -----
From: "Carl J. Denbow" <n8vz@qth.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Sunday, August 17, 2008 6:44 PM
Subject: Re: [TenTec] Status of New Display Board for OMNI VII
> Well, Mike, this is most distressing. My friend is going to be
> furious. I'm a little upset myself, because I was told by the engineer
> responsible for the board that the one he had at Dayton was final test
> version, and it was going into production shortly after the Hamvention.
> He apologized for the delay and said that it was a more complicated
> project than he'd at first thought but that it was now finally ready to
> be produced. I asked him to hold the board up so that I could take a
> picture of it. I showed this photo to my friend as proof that the board
> was on its way and that any further delay would be a short one measured
> in months not years. In fact, I remember that I actually placed a
> mobile phone call to my friend to give him a live, first-hand report
> from the Dayton Hamvention with the good news. In addition to his Orion
> II he owns several other pieces of Ten-Tec gear. The way he was talking
> he will sell all of it and swear never to buy a piece of TT gear again
> if my report from Dayton turns out to have been false. IMHO, this is
> not a good way to run a business. Personally, I'm not planning on
> selling my OMNI VII over this issue, but it does leave a bad taste in my
> mouth.
>
> 73,
>
> Carl
> N8VZ
>
>
> Mike Christiansen wrote:
>> Carl, that is a brand new webpage the Tentec just put up last week, so
>> the information IMO is current. This may not be the news your friend
>> was hoping for
>>
>> Mike, N4GW
>>
>> On Aug 17, 2008, at 6:40 PM, Carl J. Denbow wrote:
>>
>>
>>> Thanks, Mike. If this is not an old, not-updated post, I was lied to
>>> at
>>> Dayton. I was shown a prototype board and was told it was ready for
>>> production. In fact, I was told that the week after Dayton they would
>>> be having a production meeting and that the board would be ready for
>>> general sales within three months or so. A friend of mine who
>>> bought an
>>> ORION II about three years ago was told at that time that the board
>>> would be ready "in a few months." He's ready to ditch his Ten-Ten
>>> equipment he is so mad about this issue. When I gave him the
>>> information from Dayton, including my live sitting of the prototype
>>> board, he calmed down a little and said he'd give Ten-Tec a few more
>>> months. In short, I hope what I was told at Dayton is more accurate
>>> than this link. Perhaps, at this juncture Ten-Tec's recent "sins" are
>>> no more than not updating a web page! :-)
>>>
>>> Mike Christiansen wrote:
>>>
>>>> Check this link at the Tentec site. it should answer your questions
>>>>
>>>> http://radio.tentec.com/status/
>>>>
>>>>
>>>> On Aug 17, 2008, at 4:19 PM, Carl J. Denbow wrote:
>>>>
>>>>
>>>>
>>>>> Does anyone know the status the new display board that is coming out
>>>>> for
>>>>> the OMNI VII and ORION II? I saw a prototype at Dayton and was
>>>>> assured
>>>>> that it was ready for production. This board will allow, among
>>>>> other
>>>>> things, for real time, continuous spectrum scope (like the ICOM 756
>>>>> pro
>>>>> series has). I'm really looking forward to this new board, which is
>>>>> supposed to cost in the $300.00 range.
>>>>>
>>>>> Carl
>>>>> N8VZ
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec@contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>
>>>>>
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>>>
>>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|