I observed sound raspy only with AGC SLOPE 2/10dB and signals over 30dB on
s-meter.
73's Andy
----- Original Message -----
From: "John T. Fleming" <W3GQJ@earthlink.net>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Saturday, September 09, 2006 1:47 AM
Subject: Re: [TenTec] Raspy audio in 2.059d
> I just checked the setting, and it is zero. It just seems to sound raspy.
> Hmmmmmmmm.
>
> -----Original Message-----
> From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
> On Behalf Of Charles Delaune
> Sent: Friday, September 08, 2006 6:39 PM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Raspy audio in 2.059d
>
> This may sound stupid, but did you check your setting for the RX EQ under
> the Audio menu? It should be 0db for a flat response.
>
> N5BLY
>
> -----Original Message-----
> From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
> On Behalf Of John T. Fleming
> Sent: Friday, September 08, 2006 1:15 PM
> To: TenTec Reflector
> Subject: Re: [TenTec] Raspy audio in 2.059d
>
> Rick,
>
> I did all of the resets. No change. I did notice that I keep the
bandwidth
> at 2300 for SSB. If I increase the bandwidth to 2450, the 2.4 filter is
not
> in line and because of the increase of the "high" sounds; the noise is not
> as noticeable. I will wait and see what other replies I receive. Thanks
> for the suggestions.
>
> 73,
> John
>
> -----Original Message-----
> From: Rick Williams [mailto:rick.williams@telus.net]
> Sent: Friday, September 08, 2006 1:20 PM
> To: W3GQJ@earthlink.net
> Subject: RE: [TenTec] Raspy audio in 2.059d
>
> John I have not noticed the raspy signal. I have, however, encountered
> something similar on previous upgrades. The solution, for me, was:
>
> 1) Master Reset (Power on holding MAIN RX/TX)
> 2) Power off >> Power back on
> 3) RAM reset (Power on holding VFO B "LCK" button)
> 4) Power off >> Power back on
>
> It worked for me.
>
> 73,
>
> Rick
> VE7TK
>
> Website: http://www3.telus.net/ve7tk
>
> ---------------
> Date: Fri, 8 Sep 2006 06:59:26 -0400
> From: "John T. Fleming" <W3GQJ@earthlink.net>
> Subject: [TenTec] Raspy audio in 2.059d
> To: "TenTec Reflector" <tentec@contesting.com>
>
> I notice a bit of raspy audio in the new version 2.059d software. I am
> using the external Orion speaker which has a fair amount of bass response.
I
> can hear a bit of raspy noise like I have the NR turned on, even though it
> shows off. Anyone else experience the same thing? Thanks.
>
>
>
> 73,
>
> John
> <\
> ----- \ 0 _
> ----------- _\\/\-%
> ______(_)===(_)____
>
>
>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|