OK, I was curious... so I went and installed v1.373b5 this evening. Lasted
about 1 hour. Went back to 2.056.
I had used 1.372 for a while, never tried 1.373b5 so I ws curious - some
folks on the reflector like it a lot.
1.373b5 had GREAT NR, my TX audio sounded good in the monitor, FWIW. But,
the sweep wouldn't keep up with all but the slowest tuning, the NR sometimes
turned itself on and off without regard to the status displayed on the
screen, and without NR engaged the bands sounded way harsh, raspy and hard
to listen to.
OK, back to v2.056. All better, except the NR now is not too useful.
Everything else works FB, though. The bands have magically cleared up -
they sound the way I remember them sounding yesterday.
OBTW, I did my standard empirical test for noise... run the 500W amp into
the dummy load, key the mike, remain silent and watch the power meter at its
lowest setting while adjusting the SP. On v1.373b5 I could run anything up
to 7 with no backgound noise - less than 1/2 watt indicated output. Running
the SP at 8 gave me about 2 watts, at 9 gave me 5 watts, plus the scope
showed a jagged audio signal. Thats about what I remember from 1.372 -
IIRC, I ran the SP at 5 or 6 usually.
So, try it again with v2.056 loaded, and I can run the SP all the way up to
9, no problem, less than 1 watt output power. SP of 8 or less is very
quiet, power meter hardly twitches.
So, not a scientific test, just my quick way of checking for hum RF hash,
etc. in my audio. It does NOT mean that 2.056 has the same "talk power"
that v1.3x did - but at least its clean audio.
Bottom line, v2.056 is better than I thought, and a bigger improvement over
v1.372 than I remembered.
YMMV,
==============================
73 de Chuck, WS1L
charles_chandler@comcast.net
==============================
----- Original Message -----
From: <CATFISHTWO@aol.com>
To: <tentec@contesting.com>
Sent: Tuesday, July 18, 2006 11:33 AM
Subject: Re: [TenTec] What version?
>
> I was using 1.372 for quite a while but am now using 2.056 with no
> problems.
> I did have to reset several parameters, ( tx eq, mic gain, sp on sb and
> several others, but I do like it now. it works.. I'm happy check out the
> shack
>
> _http://hometown.aol.com/catfishtwo/N6AJR.html_
> (http://hometown.aol.com/catfishtwo/N6AJR.html)
>
> tom N6AJR
>
> ==============================================
>
>
>
> In a message dated 7/18/2006 7:40:55 A.M. Pacific Daylight Time,
> jhreed@chilitech.net writes:
>
> Thank you Brent, appreciate the comments... Jim Reed, ver 1.373b5
> ----- Original Message -----
> From: R. Brent Zook
> To: Discussion of Ten-Tec Equipment
> Sent: Tuesday, July 18, 2006 10:24
> Subject: Re: [TenTec] What version?
>
>
> I use version 1.372. I don't care for the problems mentioned ad nauseum
> on this site which are associated with Version 2, though version 2 seems
> more stable. And in version 1.373, I notice that the automatic
> selection of roofing filter is not tied as closely to the selection of
> the DSP bandwidth as it is in 1.372.
>
>
>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|