TenTec
[Top] [All Lists]

Re: [TenTec] Thoughts about Omni V filters

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Thoughts about Omni V filters
From: "Dave Edwards" <kd2e@comcast.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Thu, 17 Nov 2005 10:50:31 -0500
List-post: <mailto:tentec@contesting.com>
I have an Omni VI+, and like it a bunch. But...If you are in to QRP, you 
GOTTA get
an Argo V!!
I have one, and it is amazing!  And just as much fun!

....Dave
----- Original Message ----- 
From: "Darwin, Keith" <Keith.Darwin@goodrich.com>
To: <tentec@contesting.com>
Sent: Thursday, November 17, 2005 9:45 AM
Subject: [TenTec] Thoughts about Omni V filters


> Hey folks,
>
> I'm new to the list, but not new to TenTec.  Well actually, I may have
> been on the list 5 or 6 years ago but I don't recall.
>
> I run mainly (not exclusively) CW and enjoy QRP.  I've been a ham off
> and on for 30 years and am just returning after a 5 year QRT period.  It
> seems in my 30 years I've ALWAYS been QRT during sunspot cycle peaks and
> then active during valleys.  Here we go again.
>
> I am about to receive a new-used Omni V and am wondering about filters.
> A couple of questions:
>
> 1.  9 MHz vs 6.3 MHz filters:  IIRC, the first IF is 9 MHz so the 9 MHz
> filter will perform more like a roofing filter than the 6.3 MHz filter
> will.  So I assume the 9 MHz filter will produce greater benefit to
> dynamic range than the 6.3 will.  True?  If I had only one narrow filter
> is it better to have it in the 9 or 6.3 MHz position?
>
> 2.  Which filters are the ones to pick for CW use?  I assume 500 Hz at 9
> MHz and both 500 and 250 Hz in the 6.3 MHz position.  How about 1.8 KHz
> at 9 MHz and 500 & 250 at 6.3?
>
> 4.  TenTec's 250 Hz filters are 6 pole.  Inrad's are 8 I believe.  Why
> did TenTec not use 8 poles?  I assume to reduce ringing & overall
> attenuation.
>
> 5.  Are the TenTec filters OK or should I really go Inrad?  I recall
> with my prior TenTecs (Omni D & Corsair II) having more leakage around
> the filter than I wanted.  I assume an Inrad filter would have less but
> that's an assumption.
>
> I'm finding there is a real problem with TenTec rigs.  I can't stop at
> just one.  I have an Omni V on the way and I'm *still* wanting a Corsair
> II, Century 22 and of course the new Argonaut V and Orion II.  *Sigh*
>
> - Keith   -
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec 

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>