not too loud but I do hear it
----- Original Message -----
From: "Toby Pennington" <toby423@earthlink.net>
To: "Steve Baron - KB3MM" <SteveBaron@StarLinX.com>; "Discussion of Ten-Tec
Equipment" <tentec@contesting.com>
Sent: Friday, July 15, 2005 21:50
Subject: Re: [TenTec] Fw: Cooling fans and IF gain
> How bout that fan on the 963 switcher.......the first time I heard it I
> though some kind of aircraft was headed my way! Toby W4CAK
>
>
>
> ----- Original Message -----
> From: "Steve Baron - KB3MM" <SteveBaron@StarLinX.com>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Friday, July 15, 2005 3:49 PM
> Subject: Re: [TenTec] Fw: Cooling fans and IF gain
>
>
> > Interesting.
> >
> > I got the TT 963 supply with my Orion. I was surprised the first time
its
> > fan turned on. Just sitting on the desk with the Orion in RCV, the fan
> will
> > run once in a while.
> >
> > ----- Original Message -----
> > From: "Mike Coogan W7MGC" <mikegc@pacifier.com>
> > To: <tentec@contesting.com>
> > Sent: Friday, July 15, 2005 18:09
> > Subject: [TenTec] Fw: Cooling fans and IF gain
> >
> >
> > > I noticed the same heat build up on the 962 p.s. for my Omni 6+ when
> > > running Rtty. I mounted a TT 310 fan on the heat sink of the power
> > > supply, powered from the 12v dc outlet on the p.s.
> > >
> > > Mike W7MGC
> > > Vancouver, Washington
> > >
> > > Omni 6+ >>253 Auto Tuner>>HercII amp, Love it!
> > >
> > >
> > > ----- Original Message -----
> > > From: "Robert & Linda McGraw K4TAX" <RMcGraw@Blomand.Net>
> > > To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> > > Sent: Friday, July 15, 2005 6:08 AM
> > > Subject: Re: [TenTec] Cooling fans and IF gain
> > >
> > >
> > > > Interestingly enough, the Omni VI+ PA is rated at 100% duty cycle
> > > > while the
> > > > 961 power supply is not. I've found that additional cooling on the
> > > > power
> > > > supply is necessary in high duty cycle modes, partly caused by the
> > > > bridge
> > > > rectifier being mounted to the bottom plate for heat dissipation. A
> > > > small
> > > > 12V fan blowing on the heat sink in the rear takes care of the
> > > > problem.
> > > > Also, one might take note that if the power supply is sitting flat
on
> > > > the
> > > > desk there is little room at the bottom rear for vertical air
> > > > convection.
> > > > If possible, elevate the power supply, allow the heat sink to hang
off
> > > > of
> > > > the rear support and allow the heat sink to have more "breathing
> > > > room".
> > > >
> > > > As to the Omni VI+, I've found that heat build up within the radio
> > > > does
> > > > cause some frequency drift primarily due to BFO frequency changes.
I
> > > > changed my BFO's to TXCO's and found a nice improvement. All in
all,
> > > > probably not worth the investment, time and effort, for such a small
> > > > benefit.
> > > >
> > > > I've read cases where one removed the speaker, replaced it with a
> > > > computer
> > > > type 12 V fan that made improvements of about the same magnitude to
> > > > the
> > > > radio. This would be a lot less work and a lot less $$.
> > > >
> > > > 73
> > > > Bob, K4TAX
> > > >
> > > >
> > > > ----- Original Message -----
> > > > From: "Chuck Guenther" <ni0c@earthlink.net>
> > > > To: <tentec@contesting.com>
> > > > Sent: Thursday, July 14, 2005 8:17 PM
> > > > Subject: [TenTec] Cooling fans and IF gain
> > > >
> > > >
> > > >> N6KB wrote: "I find that operating my Omni VI in CW contests a fan
on
> > > >> the
> > > >> PA heat
> > > >> sink is necessary. My Kenwood TS-440 has a built-in fan with
> > > >> temperature
> > > >> controlled speed, or at least duty cycle. The TS-440 receiver
> > > >> performance in contest conditions does not compare to the Omni VI
> > > >> though. I wish Ten-Tec would have included a built in fan. I have
> > > >> never
> > > >> tried, or thought that I needed, a fan to ventilate the insides of
> > > >> the
> > > >> Omni VI though."
> > > >>
> > > >> I used a TS-440S for about seven years (in fact I still have it).
> > > >> The
> > > >> only time the cooling fan ever came on was during an RTTY contest
(I
> > > >> was
> > > >> running about 60 watts). It never came on when operating CW or
SSB.
> > > >>
> > > >> With the Ten Tec rig, I find the heat sink of my 961 PS always runs
> > > >> at a
> > > >> higher temperature than the Omni 6 PA heat sink.
> > > >>
> > > >> Today, in order to alleviate my gain problem, I swapped out the Ten
> > > >> Tec
> > > >> 221 filter for the INRAD 753 (which has a few dB less insertion
> > > >> loss).
> > > >> The gain seems adequate (and more stable) now, so perhaps my
problem
> > > >> was
> > > >> in the filter, or the connections thereto.
> > > >>
> > > >> 73,
> > > >> Chuck NI0C
> > > >> .
> > > >> _______________________________________________
> > > >> TenTec mailing list
> > > >> TenTec@contesting.com
> > > >> http://lists.contesting.com/mailman/listinfo/tentec
> > > >>
> > > >
> > > >
> > > > _______________________________________________
> > > > TenTec mailing list
> > > > TenTec@contesting.com
> > > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
> >
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|