Carl Moreschi wrote:
>Ron,
>
>If you have nothing plugged into TXEN and TXOUT on the pegasus, then TXLoop
>must be off to allow transmit. If turning TXLoop on causes it to transmit
>with nothing plugged into TXEN and TXOUT, then clearly you have a hardware
>problem. These are amplifier timing connections. Without an amplifier,
>TXLoop should always be off, and nothing should be plugged into TXEN and
>TXOUT on the back of the rig. Maybe you have something plugged in these
>jacks by mistake.
>
>73,
>
>Carl Moreschi N4PY
>Franklinton, NC
>----- Original Message -----
>From: "Ron" <k8fg@sbcglobal.net>
>To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
>Sent: Sunday, March 20, 2005 6:14 PM
>Subject: Re: [TenTec] NO XMIT WITH PTT
>
>
>
>
>>Steve N4LQ wrote:
>>
>>
>>
>>>I don't quiet follow you. Are you saying if you left click the TX Loop
>>>button at the top, it goes into transmit or do you mean it allows you to
>>>
>>>
>go
>
>
>>>into transmit? If it's the former, it almost sounds like your PTT line is
>>>shorted somewhere and when you "close the loop" in software, it
>>>
>>>
>transmits.
>
>
>>>I still think you should download the TT software and try it first. That
>>>will eliminate some confusion since it's rather basic.
>>>Check the PTT voltage at the jack per the manual between Gnd and Ptt. You
>>>should have between 4 and 5 volts.
>>>Steve Ellington
>>>N4LQ@iglou.com
>>>----- Original Message -----
>>>From: "Ron" <k8fg@sbcglobal.net>
>>>To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
>>>Sent: Sunday, March 20, 2005 4:57 PM
>>>Subject: Re: [TenTec] NO XMIT WITH PTT
>>>
>>>
>>>
>>>
>>>
>>>
>>>>Steve N4LQ wrote:
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>>Ron
>>>>>Tx Loop button? What's that? In the "Transmitter" menu, I have a
>>>>>
>>>>>
>"Enable
>
>
>>>>>keying loop" button. Is that what you meant? I have mine disabled since
>>>>>
>>>>>
>I
>
>
>>>>>don't use a TT amp with the Peg. On your N4PY front panel, do you have
>>>>>
>>>>>
>the
>
>
>>>>>"Xmit Disable" activated? If so, disable it. Also check the "ACCInp"
>>>>>button.
>>>>>For microphone input it should be disabled.
>>>>>If all this doesnt work, try the basic TenTec software and start all
>>>>>
>>>>>
>over.
>
>
>>>>>Out of ideas. 73
>>>>>Steve Ellington
>>>>>N4LQ@iglou.com
>>>>>----- Original Message -----
>>>>>From: "Ron" <k8fg@sbcglobal.net>
>>>>>To: <tentec@contesting.com>
>>>>>Sent: Saturday, March 19, 2005 2:16 PM
>>>>>Subject: [TenTec] NO XMIT WITH PTT
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>>Hello to the Group,
>>>>>>I have a couple of questions .
>>>>>>I have a Pegasus that will not Xmit via the Mic or Acc jacks
>>>>>>but will key via the N4PY software with a mouse click on the
>>>>>>TX Loop button.. Any ideas ?
>>>>>>
>>>>>>Also is there ant service info available ?
>>>>>>Thanks, Ron/K8FG...
>>>>>>_______________________________________________
>>>>>>TenTec mailing list
>>>>>>TenTec@contesting.com
>>>>>>http://lists.contesting.com/mailman/listinfo/tentec
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>_______________________________________________
>>>>>TenTec mailing list
>>>>>TenTec@contesting.com
>>>>>http://lists.contesting.com/mailman/listinfo/tentec
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>Hi Steve and Carl,
>>>>I have the latest ver of software and in the top row of buttons there is
>>>>a Tx Loop button after the Calibrate.
>>>>When I left click on this button it will go into xmit. If I go into the
>>>>settings/transmitter menu and
>>>>uncheck Keying Loop the rig goes into xmit. ACCInp is disabled.
>>>>I am starting to believe I have a rig problem, if I short the Ptt pin in
>>>>the mic connector to ground
>>>>there is no xmit also did the same test with the Acc connector with the
>>>>same results.
>>>>Ron/K8FG...
>>>>_______________________________________________
>>>>TenTec mailing list
>>>>TenTec@contesting.com
>>>>http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>>>
>>>>
>>>>
>>>>
>>>_______________________________________________
>>>TenTec mailing list
>>>TenTec@contesting.com
>>>http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>>
>>>
>>>
>>>
>>Hi Steve,
>>When I left click the button it xmit's. I just checked the ptt voltage,
>>it reads -.707 I don.t have a manual
>>other than basic operation.
>>Ron/K8FG...
>>_______________________________________________
>>TenTec mailing list
>>TenTec@contesting.com
>>http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>
>_______________________________________________
>TenTec mailing list
>TenTec@contesting.com
>http://lists.contesting.com/mailman/listinfo/tentec
>
>
>
Hi Carl,
Also noticed the CW jack is inop and no keyer operation when enabled in
the CW settings.
I looked inside the rig and it looks like the CW jack is coming apart.
This was a recent used purchase.
Ron/K8FG...
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|