Yes. Just ordered two reed relays for my OMNI V. $13 and change a pop from
T.
----- Original Message -----
From: "Jim Weisz" <k2np@lycos.com>
To: <sdprat@worldnet.att.net>
Cc: <tentec@contesting.com>
Sent: Tuesday, February 08, 2005 18:13
Subject: RE: [TenTec] Paragon question(relays)
Hi Scott.
Saw your posting about the relays being available at Digi-key..
The relays in my Paragon are HASCO KLTIC6DC12, and I could not find that
manufacturer in the Digi-Key catalog.. Did you have an alternate part
number from a different manufacturer that Digi key does carry?..
thanks.. 73, Jim K2NP
----- Original Message -----
From: "Scott Prather" <sdprat@worldnet.att.net>
To: tentec@contesting.com
Subject: RE: [TenTec] Paragon question
Date: Tue, 1 Feb 2005 18:45:59 -0800
>
> Paul-This problem is almost certainly related to the filter relays on the
> LPF board. Early Paragons used reed relays to select the LPFs, but this
was
> a pretty expensive approach. As a result, in later units Ten-Tec started
> using inexpensive frame relays instead. I had a Paragon that would do the
> same thing you describe only on the 80 M band, and lightly tapping the top
> of the cabinet near the PA heat sink would bring signals back to normal.
>
> The relays are available from Digikey, they only cost about $1.35 each.
If
> you decide to replace the defective relay, I highly recommend that you
> replace all 14, it's a lot of work to get the LPF board out and I can
almost
> guarantee that another one will probably fail if you leave the other
> originals in place. However, check to see what type of relays you have
> first. You wouldn't want to replace all 14 if your LPF board uses reed
> relays.
>
> Scott
> N7NB
>
> -----Original Message-----
> From: tentec-bounces@contesting.com
> [mailto:tentec-bounces@contesting.com]On Behalf Of
> ultrafixedwing@juno.com
> Sent: Tuesday, 01 February, 2005 17:00
> To: tentec@contesting.com
> Subject: [TenTec] Paragon question
>
>
>
> If I tune up from 6.000 mHz, when I hit 6.500 there is a click and the
> signal strength drops way, way off. I can hear signals very faint. I
> continue up to 10.500 and it clicks and signal strength kicks back up. Any
> ideas how to cure this?
> Thanks,
> Paul
> KS2S
>
> ___________________________________________________________________
> Speed up your surfing with Juno SpeedBand.
> Now includes pop-up blocker!
> Only $14.95/month -visit http://www.juno.com/surf to sign up today!
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
--
_______________________________________________
Find what you are looking for with the Lycos Yellow Pages
http://r.lycos.com/r/yp_emailfooter/http://yellowpages.lycos.com/default.asp?SRC=lycos10
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|