I will do this and let all know what I find.
Jay - KT5E
----- Original Message -----
From: "Duane A Calvin" <ac5aa@juno.com>
To: <kt5e@arrl.net>
Sent: Thursday, August 19, 2004 11:29 PM
Subject: Re: [TenTec] Omni VI locking up
> Hi Jay,
> It almost sounds as if the current draw on transmit is causing
> the voltage to drop when you press the key. Youm might want to put a
> volt meter on the power connection at the rear of the rig and watch what
> happens. Reseat and check all power connections to the radio. A
> resistive connection will drop the voltage far enough to cause some of
> the symptoms you are describing. That's where I'd start, anyway.
>
> 73, Duane
>
>
> On Thu, 19 Aug 2004 22:04:20 -0500 "Jay Schwisow" <kt5e@arrl.net> writes:
> > Ken,
> >
> > I have not tried all the buttons to unlock the rig. Again, it does
> > not lock
> > in transmit it just clicks a relay and the display goes blank.
> >
> > This has happened with the iambic key hooked directly to the rig and
> > most
> > recentlry through a W5XD IF. It has never locked in SSB but then
> > again I
> > have only had 2-3 Qs on SSB.
> >
> > It has happened on 15, 17, 20,30 and 40 meters.
> >
> > Meter illumination dims.
> >
> > Not sure about LEDs....I will pay attention to this.
> >
> > Thanks,
> >
> > Jay - KT5E
> > ----- Original Message -----
> > From: "Ken Brown" <ken.d.brown@verizon.net>
> > To: "Jay Schwisow" <kt5e@arrl.net>; <tentec@contesting.com>
> > Sent: Thursday, August 19, 2004 1:20 AM
> > Subject: Re: [TenTec] Omni VI locking up
> >
> >
> > > What other methods (besides power cycling) unlock it? How about
> > reducing
> > > the PWR control on the rig? Will that unlock it? That information
> > would
> > > be one more clue as to what is happening.
> > >
> > > How are you keying it? Microphone PTT button? Straight key to
> > keying
> > > input jack? External keyer to keying input jack? Paddle connected
> > to
> > > internal keyer? Does it do the same thing with any of these
> > keying
> > > methods? Does it matter what band you have it on? Do meter
> > illumination
> > > lamps dim, or just LED display affected? LEDs next to pushbuttons
> > go out?
> > >
> > > >intermittent problems with my Omni VI (Opt 3 upgrade) on CW.
> > > >Keying it up on CW will sometimes lock the rig (not transmitting)
> > and
> > blank
> > > >the display. There is a pretty good "klunk" when it does this.
> > Usually,
> > > >just turning rig off and back on for it to reset and go on.
> > > >
> > > >This happens into a nicely matched antenna 100 feet from the
> > shack or
> > > >straight into a dummy load so it does not appear to be outside
> > RF.
> > > >
> > > >It happens with power settings from 50 watts to 100watts. I
> > have not
> > spent
> > > >alot of time at 5 watts to see if it will happen QRP. Has anyone
> > seen
> > this
> > > >before?
> > > >
> > > >Any suggestions?
> > > >
> > > >
> > > >
> > > >
> > >
> > >
> > >
> >
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> >
>
>
> --------------------------------------
> Duane Calvin, AC5AA
> Austin, Texas
>
> http://home.austin.rr.com/ac5aa
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|