Well of course AFC does not stop drift on a xmtr. But if AFC works, the rcvr
will lock onto the incoming signal. A frequency stability of better than
10Hz is really asking a lot from amateur radio gear of any kind and thats
why good PSK programs have the AFC function.
I think the 'dire warning' about cleaning switch contacts is meant to get
across the point that one should not use typical 'TV tuner' spray to clean
the contacts. I also believe Ten Tec recommends a cleaner/lubricant that
they use themselves.
Good luck.
Tom - W4BQF
----- Original Message -----
From: "Bob Towers" <mm3kdz@beeb.net>
To: <tentec@contesting.com>
Sent: Tuesday, March 30, 2004 2:31 PM
Subject: Re: [TenTec] Corsair II warble
Tom,
Thanks for your comments...
There's no crystal for the worst band, 14.000 MHz!
I'll have a look at the band switch contacts. The Corsair manual has a dire
warning in it about cleaning the bandswitch contacts - something to do with
the lube they used on assembly.
And yes, the AFC does handle the drift, but:
a) on some data modes on MixW the AFC button is greyed out, ie MFSK, which
is the most difficult to tune
b) AFC doesn't stop warble on transmit!
73,
Bob
MM3KDZ
*********** REPLY SEPARATOR ***********
On 30/03/2004 at 12:39 Tommy wrote:
>Bob....
>
>Alan has a good point. If you look at the schematic of the Corsair, you
>will
>find the xtal mixing scheme used for each band. There may be some
>possibility for you to replace the xtals for the 'bad' bands with more
>stable xtals...along with some temperature compensating capacitors in each
>band's circuit. It could possibly provide you with the stability your
>looking for in that rig. You also might think about really cleaning the
>contacts on the band switch really good as with age, those switch contacts
>do tend to get 'dirty'.
>
>But isn't it also true that AFC in most PSK programs will easily handle the
>present drift you are experiencing?
>
>Tom - W4BQF
>
>----- Original Message -----
>From: "Bob Towers" <mm3kdz@beeb.net>
>To: <tentec@contesting.com>
>Sent: Tuesday, March 30, 2004 8:22 AM
>Subject: Re: [TenTec] Corsair II warble
>
>
>
>
>*********** REPLY SEPARATOR ***********
>
>On 30/03/2004 at 07:51 Tommy wrote:
>
>>Unfortunately Bob, you have a good radio that was designed many years
>>before
>>digital modes were used and at that time, the stability you are quoting
>>would be way above par for those radios. If your getting a max of 10Hz
>freq
>>drift, count your blessings. The PTO is not going to do any better.
>>
>>Tom - W4BQF
>>
>Tom,
>
>Many thanks for the reply...
>
>You are right, but what intrigues - and annoys me - is that on 15m and 30m
>the stability is more than good enough for me. If the PTO is this good on
>these bands, how come it deteriorates when running 20m, for instance? It's
>a
>mystery to me. Also, I have a Kenwood TS-120V which isn't a patch on the
>Corsair as far as performance is concerned but which has pretty good
>stability, better than the Corsair on 20m.
>
>73
>
>Bob
>MM3Kdz
>
>
>_______________________________________________
>TenTec mailing list
>TenTec@contesting.com
>http://lists.contesting.com/mailman/listinfo/tentec
>
>_______________________________________________
>TenTec mailing list
>TenTec@contesting.com
>http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|