Re: [Orion] Raspy Receive CW Note Problem Solved

[Joe Giacobello <k2xx@swva.net>]

Rich, thanks for your confirmation that this is a known problem and that 
a master reset eliminates it.  BTW, the problem resurfaced last night 
about 60 minutes after I had tried the reset.  I have not connected the 
behavior with any particular mode or function being on.  I have only 
used the Orion on CW so far.  I do use the sweep.  I noticed that the 
received signals did indeed seem poor and the band (40M) sounded very 
noisy last night.  I wasn't sure whether it was the RX or the band was 
lousy.  (Unfortunately, about three days after I received the Orion, my 
1000MP lost its audio and I had no way of comparing the two.)  I didn't 
notice any lettering as you describe and I never lost TX function, but 
I'll be checking things again this morning.

Up to this point, the unit had been working well and I had been fine 
tuning parameters according to the manual and Sinisa's and Yuri's 
suggestions.  I actually thought the September revision to the manual 
was pretty good.  I notice that Sinisa's and the manual's "all purpose" 
AGC recommendations differ, but I'll be comparing them more thoroughly 
as I get to understand the AGC parameters better and become more 
familiar with the rig.

Thanks for your help.


73, Joe

Richard Detweiler wrote:

> Joe,
>
> Glad you got your Orion,  I think you'll come to really love it.  It's 
> the best thing going today for RX performance.
>
> The problem you found seems to be a common problem many of us are seeing.
>
> When this happens, if you can,  try to record all you can and send it 
> into ditnbits.  It may not be all that practical, but we all try.
>
> It may or may not be a microcode problem,  don't have an answer to 
> that yet.
>
> I'm seeing a couple of different symptoms,
>
> 1) the RX just gets poor,  signal is there but weak and distorted.,  
> No display changes all controlls seem to work,  I just master reset 
> and go on.
>
> 2) The RX Stops No Signal,  static though, and TX stops,  there is the 
> lettering "DSP T/O 0" next to the send 2 key on the screen.  Again, 
> master reset, and back on the air.
>
> These happen at inopportune times,  I've tried to keep the sweep off 
> as it reduces the number of occurances.  Yet I've had it happen even 
> with the sweep off.  It may be related to the PC polling the rig.
>
>
> 73's
> Rich
> K5SF
>
>
> > From: Joe Giacobello <k2xx@swva.net>
> > Reply-To: k2xx@swva.net
> > To: orion@contesting.com, tentec@contesting.com
> > Subject: [Orion] Raspy Receive CW Note Problwm Solved
> > Date: Thu, 18 Mar 2004 00:04:06 -0500
> >
> > It took a master reset.  Don't understand why the problem arose in 
> > the first place.  I was copying CW on 30M when all of a sudden the 
> > problem appeared.  Finally decided on trying a master rest after 
> > having changed power supplies without any improvement.
> >
> > 73, Joe
> >
> > _______________________________________________
> > Orion mailing list
> > Orion@contesting.com
> > http://lists.contesting.com/mailman/listinfo/orion
>
>
> _________________________________________________________________
> Find a broadband plan that fits. Great local deals on high-speed 
> Internet access. http://click.atdmt.com/AVE/go/onm00200360ave/direct/01/
>
> _______________________________________________
> Orion mailing list
> Orion@contesting.com
> http://lists.contesting.com/mailman/listinfo/orion

_______________________________________________
Orion mailing list
Orion@contesting.com
http://lists.contesting.com/mailman/listinfo/orion