Sorry for all the confusion I created with the typo!
Yes Carl, I do a master reset after each install, even tried the "LCK"
button reset. Downloaded the firmware again and compared the file with the
first one ... they're identical! Ran the verify process several times and
it stops at line 9280 (9272 on Orion screen).
Attempted to re-install version 1.367 and found RIT still messed up. It
wouldn’t verify either, stopped at line 9230 (9226 on Orion screen).
Changed serial cable and put version 1.369 back in. No improvement.
As it looks at the moment, turning the RIT in one direction, the screen
shows it jumping from 0 to –10 (or +10) and back to 0. Change the PBT/BW
step to 50 and the RIT jumps from 0 to 50. PBT step set to 100, it jumps
from 0 to 100. The “+” or “-“ indication appears to reverse when the RIT
knob is pushed in. Same symptoms with XIT and sub-receiver.
73's ... Kip
- http://www.qsl.net/wb3afl/hamrlt.html
- Collinsville Weather:
http://www.qsl.net/wb3afl/wx/display.html
----- Original Message -----
From: "Carl Moreschi n4py-at-earthlink.net |TenTec|"
<4y6fhsyc790t@sneakemail.com>
To: <XXXXXXXXXXXXXXXXXXXXX>
Sent: Wednesday, February 11, 2004 10:25 PM
Subject: Re: [TenTec] RX/TX Broken in Orion Version 1.369?
In my opinion, standard procedure anytime a new firmware version is loaded,
is to then do a master reset. That's what I always do. Version 1.369 is
really looking good here.
Carl Moreschi N4PY
Franklinton, NC
----- Original Message -----
From: "Kip Glunt" <r5lul3j02@sneakemail.com>
To: <tentec@contesting.com>
Sent: Thursday, February 12, 2004 2:58 AM
Subject: Re: [TenTec] RX/TX Broken in Orion Version 1.369?
> Sorry .... I meant RIT/XIT...
>
>
> 73's ... Kip
>
> - http://www.qsl.net/wb3afl/hamrlt.html
> - Collinsville Weather:
> http://www.qsl.net/wb3afl/wx/display.html
>
>
>
> ----- Original Message -----
> From: "John L Merrill jmerrill1-at-adelphia.net |TenTec|"
> <c1dthsyafq0t@sneakemail.com>
> To: <XXXXXXXXXXXXXXXXXXXXX>
> Sent: Wednesday, February 11, 2004 9:47 PM
> Subject: RE: [TenTec] RX/TX Broken in Orion Version 1.369?
>
>
> What do you mean by RX/TX? You can't transmit or receive? :-)
>
> John N1JM
>
> -----Original Message-----
> From: tentec-bounces@contesting.com
> [mailto:tentec-bounces@contesting.com]On Behalf Of Kip Glunt
> Sent: Wednesday, February 11, 2004 9:26 PM
> To: Ten-Tec List
> Subject: [TenTec] RX/TX Broken in Orion Version 1.369?
>
>
> Seems that RX/TX is broken in version 1.369. Anyone else having this
> problem?
>
>
> 73's ... Kip
>
> - http://www.qsl.net/wb3afl/hamrlt.html
> - Collinsville Weather:
> http://www.qsl.net/wb3afl/wx/display.html
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|