I use a full 25 wire cable on my VI Plus, some of the other pins tell
my 253 which band I am on..
Dave W7DPW
----- Original Message -----
From: "Steve Baron - KB3MM" <SteveBaron@StarLinX.com>
To: <tentec@contesting.com>
Sent: Monday, November 24, 2003 9:18 PM
Subject: Re: [TenTec] Omni 6 Rig Control
> MUST be a three wire cable. A full 25 wire cable will short out
signals in
> the rig.
>
> ----- Original Message -----
> From: "George Skoubis" <george.skoubis@verizon.net>
> To: <tentec@contesting.com>
> Sent: Tuesday, November 25, 2003 04:09
> Subject: RE: [TenTec] Omni 6 Rig Control
>
>
> > George,
> >
> > Writelog will connect to your computer with a simple serial port
> > cable. DB25 connector on the radio end and most likely DB9 on the
> > computer end.
> >
> > Go into any computer store and tell them what you need and it
should
> > cost you less than 20.
> >
> > Just the serial port cable will get Writelog reading the
frequency
> > from the radio, as well as jumping to the band spots if you use
packet
> > or telnet.
> >
> > If you add cables RCA plug to 1/8" stereo plug (sometimes you
also
> > need to set up isolation transformers to keep out the rf) and plug
these
> > in the audio in/out jacks on the Omni VI and the other end into
the
> > sound card in/out jacks on the computer you can also use Writelog
to
> > send recorded exchange messages (if you are a contester or a dxer
and
> > want to save your voice in the pileup).
> >
> > The serial cable will probably get you what you want to start
out
> > with, if you have questions on setup subscribe to the Writelog
reflector
> > (instructions on the Writelog home page) or try www.k9jy.com for a
> > really good Writelog setup website.
> >
> > Good luck and welcome to the computer age!
> >
> > 73 de George / KF9YR
> >
> > -----Original Message-----
> > From: tentec-bounces@contesting.com
> > [mailto:tentec-bounces@contesting.com] On Behalf Of George Tuncil
> > Sent: Monday, November 24, 2003 9:18 PM
> > To: TenTec@contesting.com
> > Subject: [TenTec] Omni 6 Rig Control
> >
> > I have an Omni 6, option 3, rig which I have had for nearly 9
years now.
> > I have finally progressed to the computer age and have a computer
in my
> > shack (don't laugh!). Anyway, I would like to know what the
preferred
> > method is for hooking up my Omni to the computer for rig control,
in
> > conjunction with my new logging software (Writelog). I read about
all
> > kinds of ways to do this, but not being much of a computer guy, or
> > wanting to hook up several different keying devices and a TNC in
my
> > already crowded shack, is there a simple device or method to do
this?
> > Thanks in advance for the help.
> >
> > George Tuncil, W6AEA
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|